Choose Product
Identify Problem
03
Find Solutions

Gibson Refrigerator ice maker not working

If your Gibson refrigerator ice maker is not working and the unit is not making ice, start with the most likely problems and work down the list: a defective main control board that fails to send voltage to the ice maker, a freezer that’s too warm, or a faulty water inlet valve. Inspect the control board for visible damage and use a multimeter to verify voltage to the ice maker. Make sure the freezer temperature is between 0 and 5°F so the ice maker can form cubes; anything above about 10°F will reduce or stop production. Check the water inlet valve for at least 20 psi of supply pressure and that it’s receiving power, since low pressure or a dead valve prevents filling. If those checks pass, the ice maker assembly itself may be bad and often is replaced as a unit. Less common causes include a stuck dispenser solenoid or a frozen or damaged fill hose, which you can thaw or replace. For exact replacement parts for your model, enter your model number on RepairClinic.com to find the right part for your refrigerator and complete the ice maker repair.

01 - Gibson Refrigerator Main Control Board

The refrigerator's main control board controls the voltage being sent to the ice maker. If the control board is defective, the ice maker may not work at all. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to determine if voltage is reaching the ice maker after reviewing the refrigerator's wiring diagram.
Enter model number to search for the required part specific to your product
Top Solution

02 - Freezer Temperature is Above 10 Degrees F (-12C)

If the freezer temperature is above 10 degrees Fahrenheit (-12 Celsius), the ice maker will not produce ice cubes efficiently. The freezer temperature should be set between 0 and 5 degrees Fahrenheit (-18 to -15 Celsius) for the ice maker to work properly.
Top Solution

03 - Gibson Refrigerator Water Inlet Valve

The water inlet valve is an electrically-controlled valve that opens to supply water to the dispenser and ice maker. If the water inlet valve is defective, or if it has insufficient pressure, it won’t allow water to flow through. As a result, the ice maker won’t make ice. The valve requires at least 20 psi to function properly. Make sure that the water pressure to the valve is at least 20 psi. If the water pressure is sufficient, use a multimeter to check for power to the water inlet valve. If the water inlet valve has sufficient pressure and is getting power, but the ice maker won’t fill with water to make ice, replace th...e water inlet valve.
Highly Likely

04 - Gibson Refrigerator Ice Maker Assembly

One component of the ice maker assembly might be defective. Since many of the ice maker components are not sold separately, you may need to purchase and replace the entire ice maker assembly. Before replacing the ice maker assembly, check the water inlet valve, water line, and fan. If none of these parts are at fault, and the freezer temperature is at least 15 degrees Fahrenheit, replace the ice maker assembly.
Common

05 - Gibson Refrigerator Dispenser Solenoid

The dispenser solenoid opens a door flap to release the ice and then closes the door flap once the dispenser finishes dispensing ice. If the dispenser solenoid is defective, the dispenser door won't open. To determine if the dispenser door solenoid is defective, use a multimeter to test it for continuity. In addition, check the dispenser actuator pin to ensure that it moves freely. If the dispenser door solenoid does not have continuity, or if the actuator pin does not move freely, replace the dispenser solenoid.
Common

06 - Gibson Refrigerator Fill Hose

If there is low water pressure coming into the refrigerator, or the water inlet valve is defective, the ice maker's fill tube can become clogged with ice and prevent water from entering the ice maker tray. You can use a hair dryer to thaw out the frozen fill tube, but you should confirm the home has sufficient water pressure and the water inlet valve is functioning properly. If the fill tube appears damaged, you should replace it with a new fill tube.
Common

Frequently Asked Questions

My ice maker is not making ice — what should I check first?
How do I test the refrigerator water inlet valve when the ice maker is not filling?
Why won’t my ice maker work if the freezer is too warm?
How can I tell if the main control board is the cause of the ice maker problem?
How do I enter my model number or part number on RepairClinic.com to find the right replacement part?

Shop by Gibson Refrigerator Parts