Choose Product

Identify Problem

Find Solutions

Haier Washer won't stop

If your Haier washer won't stop, first check for water siphoning from the tub. The drain hose outlet should end 30 to 36 inches above the floor in a standpipe or laundry tub. A hose positioned too low, sealed tightly at the standpipe, or pushed too far down the pipe can make the washer keep running as water leaves the tub. If the washer drains normally, a defective control board is the next likely cause of a washer not stopping or a washing machine stuck on a cycle. Inspect the control board for burned areas or shorted components, although it cannot be tested easily. A faulty main control board can cause the same problem. If both boards appear normal, test the timer with a multimeter and the wiring diagram, then replace it if defective. These parts control cycle timing and can leave the washer running continuously. Enter your Haier washer model number to find the exact replacement control board, main control board, or timer for your specific machine.

01 - Water siphoning from tub

If the water is siphoning from the tub the outlet end of the drain hose is likely lower than the water level in the tub. The drain hose should terminate between 30 inches to 36 inches (77 centimeters to 92 centimeters) above the floor, depending on the model, in a standpipe or laundry tub. If the drain hose is sealed at the top of the standpipe or excess hose is pushed too far down into the pipe, siphoning can also occur.

Common

02 - Haier Washing Machine Control Board

If the washer can successfully drain the water from the tub then a defective control board could be responsible for the washer not stopping. The control board cannot be easily tested, but you can try to inspect it for signs of burning or a shorted-out component to help determine if the part should be replaced.

Enter model number to search for the required part specific to your product

Need help finding your model number?

Shop all Haier Washing Machine Control Board Parts

Less Common

03 - Haier Washing Machine Main Control Board

If the washer can successfully drain the water from the tub then a defective main control board could be responsible for the washer not stopping. The main control board cannot be easily tested, but you can try to inspect it for signs of burning or a shorted-out component to help determine if the part should be replaced.

Shop all Haier Washing Machine Main Control Board Parts

Less Common

04 - Haier Washing Machine Timer

If the washer can successfully drain the water from the tub then a defective timer could be responsible for the washer not stopping. You can test the timer by using a multimeter and consulting the wiring diagram. If the timer is defective, replace it.

Shop all Haier Washing Machine Timer Parts

Less Common

Frequently Asked Questions

Why won't my Haier washer stop running?

Why does my Haier washer keep filling and draining?

How do I test the timer on a Haier washing machine that won't stop?

Could the control board cause my Haier washer to keep running?

How do I find the correct Haier washer timer or control board?

Shop by Haier Washing Machine Parts

Haier Washing Machine Agitator Replacement Parts

Haier Washing Machine Axle, Roller, Shaft, Wheel Replacement Parts

Haier Washing Machine Bag Replacement Parts

Haier Washing Machine Bearing Replacement Parts

Haier Washing Machine Belt Replacement Parts

Haier Washing Machine Bracket & Flange Replacement Parts

Haier Washing Machine Cap, Lid & Cover Replacement Parts

Haier Washing Machine Capacitor Replacement Parts

Haier Washing Machine Circuit Board & Timer Replacement Parts

Haier Washing Machine Diode, Magnetron & Resistor Replacement Parts

Haier Washing Machine Dispenser Replacement Parts

Haier Washing Machine Door Replacement Parts

Haier Washing Machine Drum & Tub Replacement Parts

Haier Washing Machine Fastener Replacement Parts

Haier Washing Machine Filter Replacement Parts

Haier Washing Machine Finished Product Replacement Parts

Haier Washing Machine Gas Burner & Control Valve Replacement Parts

Haier Washing Machine Gasket & Seal Replacement Parts

Haier Washing Machine Handle Replacement Parts

Haier Washing Machine Heating Element Replacement Parts

Haier Washing Machine Hinge Replacement Parts

Haier Washing Machine Hose, Tube & Fitting Replacement Parts

Haier Washing Machine Insulation Replacement Parts

Haier Washing Machine Knob, Dial & Button Replacement Parts

Haier Washing Machine Latch Replacement Parts

Haier Washing Machine Leg, Foot & Caster Replacement Parts

Haier Washing Machine Lighting & Light Bulb Replacement Parts

Haier Washing Machine Manuals, Care Guides & Literature Replacement Parts

Haier Washing Machine Miscellaneous Replacement Parts

Haier Washing Machine Motor Replacement Parts

Haier Washing Machine Panel Replacement Parts

Haier Washing Machine Power Cord Replacement Parts

Talk With Us

We can help you check an order, track a package, start a return, and more.

START A CHAT

Talk With Us

We can help you check an order, track a package, start a return, and more.

Join Repair Clinic's VIP email list for 10% off, plus other discounts and tips!

Our Story

Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.

About Repair Clinic

Customer Stories Repair Parts BrandsDIY Repair Blog In the News