Keep your Goodman GMPN060-3 furnace running efficiently with genuine OEM replacement parts from Repair Clinic. The GMPN060-3 is a 60,000 BTU input, 80% AFUE single-stage upflow gas furnace from Goodman’s GMPN series with a three-ton blower assembly. The GMPN designation identifies a specific control board and cabinet generation within Goodman’s 80% AFUE upflow line, distinct from the GMP075-4 and GMS80 designations on related platforms. The GMPN060-3 uses standard metal B-vent, produces no condensate, and has a straightforward non-condensing service profile. Repair Clinic stocks genuine Goodman OEM parts for the GMPN060-3 including the Goodman igniter parts, Goodman flame sensor parts, Goodman draft inducer motor parts, Goodman control board parts, and Goodman blower motor parts. Browse the Goodman furnace parts catalog filtered by GMPN060-3 for the complete parts inventory.
GMPN060-3: Goodman GMPN Series 60,000 BTU Upflow Furnace with Three-Ton Blower Assembly
The Goodman GMPN060-3 is a non-condensing upflow furnace with a three-ton blower assembly, distinct from the four-ton blower of the GMP075-4 and the five-ton blower of higher-output GMP models. Blower motor and wheel components must be confirmed against the GMPN060-3 designation before ordering, as they differ between the 3 (three-ton) and 4 (four-ton) blower configurations in the GMP series. The Goodman furnace troubleshooting guide covers fault code blink patterns for the Goodman GMPN platform control board.
Most Replaced Parts on the Goodman GMPN060-3
Hot Surface Igniter for the GMPN060-3
Testing igniter resistance at room temperature with power off confirms failure in under two minutes. An infinite ohm reading means the element is open-circuit and must be replaced before any heating cycle can complete. The GMPN060-3 igniter must heat to temperature within the control board timing window on every heating call.
Goodman GMPN060-3 Flame Sensor
The flame sensor passes a micro-amp signal through the burner flame to confirm sustained combustion after ignition. Annual cleaning with fine steel wool extends sensor service life on the GMPN platform and prevents most early-season nuisance lockouts.
Draft Inducer Motor for the GMPN060-3
The inducer is sized for 60,000 BTU combustion gas throughput. Bearing failure presents as grinding during the pre-purge phase at startup before the gas valve opens. An audible bearing should be replaced before complete seizure creates a heating emergency.
Goodman GMPN060-3 Control Board
Read and document the LED fault code before ordering any replacement. The GMPN platform control board may differ from the GMP platform board even at the same BTU output. Confirm the GMPN060-3 model designation from the data plate before ordering a replacement board.
Blower Motor for the Goodman GMPN060-3
The GMPN060-3 uses a three-ton blower motor that must not be substituted with a four-ton motor from the GMP075-4 or other higher-output designations. Test the run capacitor before ordering a replacement motor. A failing capacitor produces the same slow-start symptom as a failed motor winding at a fraction of the motor replacement cost.
Why Choose Repair Clinic for Goodman GMPN060-3 Parts
- Genuine Goodman GMPN OEM Components: Igniters, flame sensors, and three-ton blower motors confirmed for the GMPN060-3 upflow configuration Goodman furnace parts.
- GMPN vs GMP Platform Distinction: The GMPN060-3 control board and blower motor specifications are catalogued separately from the GMP075-4 to prevent cross-substitution errors between the GMPN and GMP platform generations.
- Fault Code Resources: Goodman GMPN LED blink code charts available alongside every GMPN060-3 part listing through Goodman furnace troubleshooting.
- 365-Day Returns: Return any uninstalled Goodman part within a full year of purchase with no restocking fees.
Goodman GMPN060-3 Furnace Parts FAQ
What is the BTU output and efficiency of the Goodman GMPN060-3?
The GMPN060-3 is a 60,000 BTU input, 80% AFUE single-stage upflow gas furnace from Goodman’s GMPN series. The GMPN designation identifies the 80% AFUE single-stage upflow platform with a specific control board and cabinet design, 060 identifies 60,000 BTU capacity, and 3 identifies the three-ton blower assembly.
What is the difference between the Goodman GMPN060-3 and the GMP075-4?
The GMPN060-3 delivers 60,000 BTU with a three-ton blower assembly while the GMP075-4 delivers 75,000 BTU with a four-ton blower assembly. The GMPN and GMP designations also identify slightly different control board and cabinet generations within Goodman’s 80% AFUE upflow furnace product line.
My Goodman GMPN060-3 furnace keeps locking out. Where do I start?
Read the control board LED fault code first. On any Goodman GMPN furnace the blink pattern on the LED identifies the failed component before any physical diagnosis begins. An ignition failure code points to the igniter or flame sensor in the vast majority of GMPN060-3 lockout calls.
What type of venting does the Goodman GMPN060-3 require?
The GMPN060-3 is an 80% AFUE non-condensing upflow furnace requiring standard metal B-vent. It produces no condensate and does not use PVC plastic venting.
