Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool/Kenmore Gas Dryer Pulley Wheel Replacement #279640
Whirlpool/Kenmore Gas Dryer Pulley Wheel Replacement #279640
Skill Level
Total Parts Cost
$29.50Estimated Savings
$112.5003:45
- Description
This video provides step-by-step instructions on replacing the pulley wheel in in Whirlpool gas dryers. The most common reason for replacing the pulley wheel is when the dryer doesn’t spin.
All of the information in this pulley wheel replacement video is applicable to the following brands: Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Crosley Admiral
Tools used: Hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife
All of the information in this pulley wheel replacement video is applicable to the following brands: Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Crosley Admiral
Tools used: Hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to detach the control panel.
3
Depending on your model, you will either insert a putty knife under the panel to release the two clips or you will pull off both plastic end caps and remove the screws found underneath.
4
Now, rotate the control panel up.
5
Remove the screws securing the main top and slide the top off.
6
Next, insert a flathead screwdriver between the upper and lower front panels to release the two clips and detach the lower panel.
7
Remove the upper panel mounting screws along with the lint screen duct screw and, if applicable, the screw securing the grounding wire.
8
Detach the moisture sensor wire and the two door springs.
9
Now, disconnect the door switch wire connector remove the screws from the top of the upper panel and lift the upper panel off.
10
If still intact, depress the pulley to release the belt tension and unthread the belt from the pulley and motor shaft.
11
Now use the belt to lift out the drum.
12
Use a flathead screwdriver to remove the tri-ring from the pulley arm shaft and pull off the old pulley wheel and washer.
13
You’re now ready to install the new pulley wheel.
14
Slide the washer and the new pulley wheel onto the shaft and secure it with the tri-ring.
15
Now, replace the drum by aligning its rim on the two rear rollers and loop the belt around the tension pulley and motor shaft in a “zig-zag” formation.
16
Rotate the drum to help align the belt.
17
Replace the upper front panel by aligning the two rollers on the drum rim and positioning the top lip of the panel on the cabinet brackets.
18
Replace all four panel screws along with the lint screen duct screw and, if applicable, the screw securing the grounding wire.
19
Reattach the moisture sensor wire and the door springs.
20
Now, replace the lower front panel by snapping it into position.
21
Reconnect the door switch wire connector at the top of the dryer.
22
Slide the main top on and secure it with the screws.
23
Rotate the control panel down and lock it into place.
24
If applicable, replace the screws and end caps.
25
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step instructions on replacing the pulley wheel in in Whirlpool gas dryers. The most common reason for replacing the pulley wheel is when the dryer doesn’t spin.
All of the information in this pulley wheel replacement video is applicable to the following brands: Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Crosley Admiral
Tools used: Hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife
All of the information in this pulley wheel replacement video is applicable to the following brands: Whirlpool, Kenmore, Maytag, KitchenAid, Amana, Inglis, Crosley Admiral
Tools used: Hex socket, flat-head screwdriver, Phillips head screwdriver, putty knife
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to detach the control panel.
3
Depending on your model, you will either insert a putty knife under the panel to release the two clips or you will pull off both plastic end caps and remove the screws found underneath.
4
Now, rotate the control panel up.
5
Remove the screws securing the main top and slide the top off.
6
Next, insert a flathead screwdriver between the upper and lower front panels to release the two clips and detach the lower panel.
7
Remove the upper panel mounting screws along with the lint screen duct screw and, if applicable, the screw securing the grounding wire.
8
Detach the moisture sensor wire and the two door springs.
9
Now, disconnect the door switch wire connector remove the screws from the top of the upper panel and lift the upper panel off.
10
If still intact, depress the pulley to release the belt tension and unthread the belt from the pulley and motor shaft.
11
Now use the belt to lift out the drum.
12
Use a flathead screwdriver to remove the tri-ring from the pulley arm shaft and pull off the old pulley wheel and washer.
13
You’re now ready to install the new pulley wheel.
14
Slide the washer and the new pulley wheel onto the shaft and secure it with the tri-ring.
15
Now, replace the drum by aligning its rim on the two rear rollers and loop the belt around the tension pulley and motor shaft in a “zig-zag” formation.
16
Rotate the drum to help align the belt.
17
Replace the upper front panel by aligning the two rollers on the drum rim and positioning the top lip of the panel on the cabinet brackets.
18
Replace all four panel screws along with the lint screen duct screw and, if applicable, the screw securing the grounding wire.
19
Reattach the moisture sensor wire and the door springs.
20
Now, replace the lower front panel by snapping it into position.
21
Reconnect the door switch wire connector at the top of the dryer.
22
Slide the main top on and secure it with the screws.
23
Rotate the control panel down and lock it into place.
24
If applicable, replace the screws and end caps.
25
You’re now ready to plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Parts Needed
Idler Pulley
$29.50
Total$0.00
Related Articles & Videos
07:08
Part Replacement
Whirlpool Electric Washer/Dryer Combo Dryer Idler Pulley Replacement #279640
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com