Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairAsko Washer Drain Pump Bellows Replacement #8801516
Asko Washer Drain Pump Bellows Replacement #8801516
Skill Level
Total Parts Cost
$70.75Estimated Savings
$112.5004:40
- Description
This video provides step-by-step instructions for replacing the drain pump bellows on Asko washing machines. The most common reasons for replacing the drain pump bellows is if it is damaged or leaking, causing the washer to leak or overflow.
All of the information in this drain pump bellows replacement video is applicable to the following brands: Asko
Tools sued: multi-screwdriver, T20 Torx bit, pinch clamp pliers
All of the information in this drain pump bellows replacement video is applicable to the following brands: Asko
Tools sued: multi-screwdriver, T20 Torx bit, pinch clamp pliers
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
To replace the drain pump bellows in your washer, first use a t-20 torx bit to remove the screws at the back securing the top panel.
3
Now pull the panel back and lift it up to remove.
4
Use a flathead screwdriver to depress the retaining tabs securing the control panel and pull the panel off.
5
Use the screwdriver to open the pump access door.
6
Pull the drain tube off of the door and drain any excess water.
7
Now carefully lift up the front of the washer and use a wood block or a comparable sturdy object to support it.
8
You can now remove the bottom mounting screws securing the front panel.
9
With the screws removed, remove the support and gently lower the appliance to the floor.
10
Next, uninstall the top mounting screws securing the front panel.
11
Pull the front panel out from the bottom; release the clip on the right side then push the panel to the left to remove.
12
Now use pliers to remove the pinch clamp securing the bellows assembly to the drain pump and tub.
13
Disconnect the pressure tube from the air chamber.
14
Rotate the bellows assembly clockwise to release the chamber tab from the bracket and remove the old assembly.
15
Install the new drain pump bellows by first inserting the air chamber tab into the bracket then rotate the assembly counter-clockwise to secure.
16
Connect the pressure tube to the air chamber.
17
Slide the new pinch clamps onto the bellows.
18
Position the bellows on the tub and drain pump then use pinch clamp pliers to secure the clamps.
19
Reinstall the front panel by aligning the pins on the frame with the holes in the panel while hooking the tab onto the dispenser hinge.
20
Make sure the drain pump gasket protrudes through the hole in the panel and snap the panel into position.
21
Replace the mounting screws on top.
22
Lift and support the washer to replace the bottom mounting screws.
23
With the screws installed, remove the support and lower the appliance.
24
Attach the drain tube to the pump access door and snap the door shut.
25
Reinstall the control panel by aligning the tabs with the slots in the frame and snap the panel into place.
26
Make sure the support rail is properly positioned.
27
Now slide the front edge of the top panel under the control panel.
28
Align the panel with the support rail and the pins on the frame then push down.
29
Replace the screws in the back.
30
You’re now ready to plug the power cord back in and confirm that the washer works properly.
Description
This video provides step-by-step instructions for replacing the drain pump bellows on Asko washing machines. The most common reasons for replacing the drain pump bellows is if it is damaged or leaking, causing the washer to leak or overflow.
All of the information in this drain pump bellows replacement video is applicable to the following brands: Asko
Tools sued: multi-screwdriver, T20 Torx bit, pinch clamp pliers
All of the information in this drain pump bellows replacement video is applicable to the following brands: Asko
Tools sued: multi-screwdriver, T20 Torx bit, pinch clamp pliers
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
To replace the drain pump bellows in your washer, first use a t-20 torx bit to remove the screws at the back securing the top panel.
3
Now pull the panel back and lift it up to remove.
4
Use a flathead screwdriver to depress the retaining tabs securing the control panel and pull the panel off.
5
Use the screwdriver to open the pump access door.
6
Pull the drain tube off of the door and drain any excess water.
7
Now carefully lift up the front of the washer and use a wood block or a comparable sturdy object to support it.
8
You can now remove the bottom mounting screws securing the front panel.
9
With the screws removed, remove the support and gently lower the appliance to the floor.
10
Next, uninstall the top mounting screws securing the front panel.
11
Pull the front panel out from the bottom; release the clip on the right side then push the panel to the left to remove.
12
Now use pliers to remove the pinch clamp securing the bellows assembly to the drain pump and tub.
13
Disconnect the pressure tube from the air chamber.
14
Rotate the bellows assembly clockwise to release the chamber tab from the bracket and remove the old assembly.
15
Install the new drain pump bellows by first inserting the air chamber tab into the bracket then rotate the assembly counter-clockwise to secure.
16
Connect the pressure tube to the air chamber.
17
Slide the new pinch clamps onto the bellows.
18
Position the bellows on the tub and drain pump then use pinch clamp pliers to secure the clamps.
19
Reinstall the front panel by aligning the pins on the frame with the holes in the panel while hooking the tab onto the dispenser hinge.
20
Make sure the drain pump gasket protrudes through the hole in the panel and snap the panel into position.
21
Replace the mounting screws on top.
22
Lift and support the washer to replace the bottom mounting screws.
23
With the screws installed, remove the support and lower the appliance.
24
Attach the drain tube to the pump access door and snap the door shut.
25
Reinstall the control panel by aligning the tabs with the slots in the frame and snap the panel into place.
26
Make sure the support rail is properly positioned.
27
Now slide the front edge of the top panel under the control panel.
28
Align the panel with the support rail and the pins on the frame then push down.
29
Replace the screws in the back.
30
You’re now ready to plug the power cord back in and confirm that the washer works properly.
Applicable Product Model
Recommended Tools and Accessories
Tube
$5.15
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com