Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairAsko Washing Machine Thermistor Replacement #8801474
Asko Washing Machine Thermistor Replacement #8801474
Skill Level
Total Parts Cost
$32.75Estimated Savings
$112.5003:52
- Description
This video provides step-by-step instructions for replacing the thermistor on Asko washing machines. The most common reason for replacing the thermistor is if the water is not being heated properly and the heating elements prove not to be defective.
All of the information in this thermistor replacement video is applicable to the following brands: Asko
Tools used: multi-screwdriver, T20 Torx bit, knife, zip tie
All of the information in this thermistor replacement video is applicable to the following brands: Asko
Tools used: multi-screwdriver, T20 Torx bit, knife, zip tie
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
To replace the thermistor on your washer, first pull the hoses free of the retainers on the rear panel, if applicable.
3
Now use a t-20 torx bit to remove the screws securing the panel.
4
Pull the panel off.
5
Next, remove the screws securing the back of the top panel.
6
Pull the panel back and lift it up to remove.
7
Use a flathead screwdriver to depress the retaining tabs securing the control panel and pull the panel off.
8
Disconnect the thermistor wire connecter from the control board.
9
Pull the wire through the frame and detach it from all of the wire retainers.
10
Now reach into the rear of the cabinet and unsnap the old thermistor bracket from the tub base.
11
Cut the thermistor wire to fully release the old assembly from the zip tie retainer.
12
Prepare the new thermistor for installation by first connecting the component and wire to the provided bracket.
13
Now insert the thermistor and bracket into the slot in the tub base.
14
Use a new zip tie to secure the thermistor wire.
15
Feed the remainder of the wire through the retainers.
16
Insert the connecter through the frame and attach it to the appropriate terminal on the control board.
17
Reinstall the control panel by aligning the tabs with the slots in the frame and snap the panel into place.
18
Make sure the support rail is properly positioned.
19
Now slide the front edge of the top panel under the control panel.
20
Align the panel with the support rail and the pins on the frame then push down.
21
Replace the screws in the back.
22
Replace the rear panel by inserting the tabs into the slots in the cabinet frame.
23
Secure the panel with the screws.
24
Secure the hoses in the rear panel retainers.
25
You’re now ready to plug the power cord back in and confirm that the washer works properly.
Description
This video provides step-by-step instructions for replacing the thermistor on Asko washing machines. The most common reason for replacing the thermistor is if the water is not being heated properly and the heating elements prove not to be defective.
All of the information in this thermistor replacement video is applicable to the following brands: Asko
Tools used: multi-screwdriver, T20 Torx bit, knife, zip tie
All of the information in this thermistor replacement video is applicable to the following brands: Asko
Tools used: multi-screwdriver, T20 Torx bit, knife, zip tie
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
To replace the thermistor on your washer, first pull the hoses free of the retainers on the rear panel, if applicable.
3
Now use a t-20 torx bit to remove the screws securing the panel.
4
Pull the panel off.
5
Next, remove the screws securing the back of the top panel.
6
Pull the panel back and lift it up to remove.
7
Use a flathead screwdriver to depress the retaining tabs securing the control panel and pull the panel off.
8
Disconnect the thermistor wire connecter from the control board.
9
Pull the wire through the frame and detach it from all of the wire retainers.
10
Now reach into the rear of the cabinet and unsnap the old thermistor bracket from the tub base.
11
Cut the thermistor wire to fully release the old assembly from the zip tie retainer.
12
Prepare the new thermistor for installation by first connecting the component and wire to the provided bracket.
13
Now insert the thermistor and bracket into the slot in the tub base.
14
Use a new zip tie to secure the thermistor wire.
15
Feed the remainder of the wire through the retainers.
16
Insert the connecter through the frame and attach it to the appropriate terminal on the control board.
17
Reinstall the control panel by aligning the tabs with the slots in the frame and snap the panel into place.
18
Make sure the support rail is properly positioned.
19
Now slide the front edge of the top panel under the control panel.
20
Align the panel with the support rail and the pins on the frame then push down.
21
Replace the screws in the back.
22
Replace the rear panel by inserting the tabs into the slots in the cabinet frame.
23
Secure the panel with the screws.
24
Secure the hoses in the rear panel retainers.
25
You’re now ready to plug the power cord back in and confirm that the washer works properly.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com