Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairSamsung Dishwasher Water Inlet Valve Replacement #DD62-00084A
Samsung Dishwasher Water Inlet Valve Replacement #DD62-00084A
Skill Level
Total Parts Cost
$85.77Estimated Savings
$112.5009:58
- Description
This video provides step-by-step repair instructions for replacing the water inlet valve on a Samsung dishwasher. The most common reason for replacing the water inlet valve is the dishwasher not filling properly or is filling too slowly.
All of the information for this inlet valve replacement video is applicable to the following brands:
Samsung
Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers
All of the information for this inlet valve replacement video is applicable to the following brands:
Samsung
Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers
Step By Step Instructions
1
To replace the water inlet valve in your dishwasher, you will need to uninstall the appliance first. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Use a phillips-head screwdriver to remove the screws securing the lower access panel.
4
Remove the panel.
5
Use a 5/8th inch wrench to help unthread the water supply line from the inlet valve be prepared for some water to spill.
6
Next, unthread the screw securing the junction box cover. Then pull the cover off.
7
Note the location of the wires then untwist the wire nuts to disconnect the wires.
8
Unthread the strain relief nut and detach the strain relief from the junction box.
9
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
10
Open the dishwasher door and remove the mounting bracket screws.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
You can lower the rear leveling leg by using a 9/64th inch hex-head screwdriver to rotate the adjustment rod at the front clockwise.
13
Now, very carefully pull the dishwasher away from the cabinet.
14
Tip the dishwasher back so it rests on its rear panel.
15
Next, remove the mounting screws securing the main control board cover.
16
Remove the cover.
17
Use a small flat-head screwdriver to help pry out the control board housing and move it out of the way.
18
Now remove the screws securing the inner access panel.
19
Release the mounting tabs detach the door wire conduit and lift out the panel.
20
Unthread the screw securing the inlet valve grounding wire.
21
Remove the remaining two screws securing the valve.
22
Now unthread the screws securing the left side access panel.
23
Remove the panel.
24
Release the spring clamp securing the valve outlet hose to the water panel
25
Pull the hose off.
26
Disconnect the wire connecter to fully remove the old valve.
27
Prepare the new water inlet valve for installation by transferring the outlet hose and fitting from the old valve to the new one.
28
Wrap some Teflon tape clockwise around the threads of the fitting before installing it in the new valve.
29
Make sure the fitting is facing down and slightly to the right.
30
Connect the wire connecter and position the valve on the base.
31
Secure the hose to the water panel.
32
Replace the side access panel and secure it with the screws.
33
Thread the screws to secure the valve.
34
Secure the grounding wire with the smaller screw.
35
Realign the inner access panel.
36
Snap the wire conduit into place on the panel and hook the mounting tabs on the hinge supports.
37
Replace the screws to secure the panel.
38
Realign the main control board housing tabs with the slots in the base and push the assembly into position.
39
Realign the cover and replace the screws to secure.
40
Return the dishwasher to its upright position.
41
Make sure the drain hose is accessible through the cabinet wall and that the water supply and power supply lines are positioned in their respective channels in the dishwasher base then gently slide the dishwasher back into the cabinet.
42
Adjust the leveling legs if necessary.
43
Replace the screws to secure the mounting brackets to the cabinet or countertop.
44
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
45
Make sure the hose is elevated above the connection point.
46
Fully position the wire strain relief in the junction box and secure the strain relief nut.
47
Connect the wires using the wire nuts.
48
Align the cover and replace the screw to secure.
49
Reconnect the water supply line to the inlet valve.
50
Replace the lower access panel and secure it with the screws.
51
With the repair completed turn the water supply back on as well as the power and your dishwasher should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the water inlet valve on a Samsung dishwasher. The most common reason for replacing the water inlet valve is the dishwasher not filling properly or is filling too slowly.
All of the information for this inlet valve replacement video is applicable to the following brands:
Samsung
Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers
All of the information for this inlet valve replacement video is applicable to the following brands:
Samsung
Tools needed: phillips head screwdriver, flat head screwdriver, 5/8 inch wrench, 9/64 inch hex head screwdriver, pliers
Step-By-Step Instructions
1
To replace the water inlet valve in your dishwasher, you will need to uninstall the appliance first. To do this, turn off the power to your dishwasher
2
Shut off the water supply valve.
3
Use a phillips-head screwdriver to remove the screws securing the lower access panel.
4
Remove the panel.
5
Use a 5/8th inch wrench to help unthread the water supply line from the inlet valve be prepared for some water to spill.
6
Next, unthread the screw securing the junction box cover. Then pull the cover off.
7
Note the location of the wires then untwist the wire nuts to disconnect the wires.
8
Unthread the strain relief nut and detach the strain relief from the junction box.
9
Next, disconnect the drain hose from the sink drain or garbage disposer and feed it through the cabinet.
10
Open the dishwasher door and remove the mounting bracket screws.
11
To move the dishwasher, you may need to adjust the legs to lower the appliance.
12
You can lower the rear leveling leg by using a 9/64th inch hex-head screwdriver to rotate the adjustment rod at the front clockwise.
13
Now, very carefully pull the dishwasher away from the cabinet.
14
Tip the dishwasher back so it rests on its rear panel.
15
Next, remove the mounting screws securing the main control board cover.
16
Remove the cover.
17
Use a small flat-head screwdriver to help pry out the control board housing and move it out of the way.
18
Now remove the screws securing the inner access panel.
19
Release the mounting tabs detach the door wire conduit and lift out the panel.
20
Unthread the screw securing the inlet valve grounding wire.
21
Remove the remaining two screws securing the valve.
22
Now unthread the screws securing the left side access panel.
23
Remove the panel.
24
Release the spring clamp securing the valve outlet hose to the water panel
25
Pull the hose off.
26
Disconnect the wire connecter to fully remove the old valve.
27
Prepare the new water inlet valve for installation by transferring the outlet hose and fitting from the old valve to the new one.
28
Wrap some Teflon tape clockwise around the threads of the fitting before installing it in the new valve.
29
Make sure the fitting is facing down and slightly to the right.
30
Connect the wire connecter and position the valve on the base.
31
Secure the hose to the water panel.
32
Replace the side access panel and secure it with the screws.
33
Thread the screws to secure the valve.
34
Secure the grounding wire with the smaller screw.
35
Realign the inner access panel.
36
Snap the wire conduit into place on the panel and hook the mounting tabs on the hinge supports.
37
Replace the screws to secure the panel.
38
Realign the main control board housing tabs with the slots in the base and push the assembly into position.
39
Realign the cover and replace the screws to secure.
40
Return the dishwasher to its upright position.
41
Make sure the drain hose is accessible through the cabinet wall and that the water supply and power supply lines are positioned in their respective channels in the dishwasher base then gently slide the dishwasher back into the cabinet.
42
Adjust the leveling legs if necessary.
43
Replace the screws to secure the mounting brackets to the cabinet or countertop.
44
Feed the drain hose through the cabinet and connect it to the sink drain or disposer.
45
Make sure the hose is elevated above the connection point.
46
Fully position the wire strain relief in the junction box and secure the strain relief nut.
47
Connect the wires using the wire nuts.
48
Align the cover and replace the screw to secure.
49
Reconnect the water supply line to the inlet valve.
50
Replace the lower access panel and secure it with the screws.
51
With the repair completed turn the water supply back on as well as the power and your dishwasher should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com