Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Door Boot Seal Replacement #134616100
Electrolux Door Boot Seal Replacement #134616100
Skill Level
Total Parts Cost
$61.55Estimated Savings
$112.5007:24
- Description
This video provides step-by-step repair instructions for replacing the door boot seal on an Electrolux washing machine. The most common reason for replacing the boot seal is if the washer is leaking water.
All of the information for this door boot seal replacement video is applicable to the following brands:
Electrolux
Tools needed: Phillips head screwdriver, #2 square bit, needle nose pliers
All of the information for this door boot seal replacement video is applicable to the following brands:
Electrolux
Tools needed: Phillips head screwdriver, #2 square bit, needle nose pliers
Step By Step Instructions
1
Before you replace the door boot seal in your washer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel to the support bracket.
5
Pull out the dispenser drawer and depress the button to fully release it.
6
You can now remove the remaining screws securing the control panel assembly.
7
Lift the assembly up to detach and disconnect the user interface wire connecter.
8
Use a flat-head screwdriver to help open the main control cover then disconnect the door latch wire harness.
9
Open the washer door and use needle-nose pliers to help remove the outer boot seal retainer.
10
Remove the boot seal from the lip of the front panel.
11
Lift and support the washer so you can unthread the bottom front panel mounting screws.
12
Remove the support and unthread the top front panel mounting screws.
13
Lift the panel up and out.
14
Remove the light from the boot seal.
15
Cut the zip tie securing the hose connecter and pull the connecter free of the boot.
16
Pull the bottom of the boot seal forward and push down to release the inner boot seal retainer spring.
17
Fully remove the old boot seal.
18
You’re now ready to install the new door boot seal.
19
Keeping the ports at the top, position the lip of the new seal behind the outer drum rim.
20
Once the seal is fully positioned, reinstall the inner boot retainer spring to secure – you can use a strong spring clamp to help hold the retainer spring in place as you install it.
21
We recommend using eye protection during this step.
22
With the seal secured, insert the light into the appropriate port.
23
Apply some dish soap to the hose connecter to make it easier to insert the connecter into the port.
24
Secure the connecter with a zip tie.
25
Reinstall the front panel by aligning it on the mounting pins.
26
Replace the mounting screws on top.
27
Lift and support the washer to replace the bottom mounting screws.
28
Now align the new boot seal on the lip of the front panel.
29
Secure the boot to the panel with the outer boot retainer.
30
Reconnect the door latch wire harness and close the main control cover.
31
Reinstall the control panel assembly by first reconnecting the user interface wire connecter.
32
Realign the panel on the support bracket and rethread all of the mounting screws.
33
Replace the dispenser drawer.
34
Realign the main top and slide it into place.
35
Rethread the screws in the back.
36
With the repair completed plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the door boot seal on an Electrolux washing machine. The most common reason for replacing the boot seal is if the washer is leaking water.
All of the information for this door boot seal replacement video is applicable to the following brands:
Electrolux
Tools needed: Phillips head screwdriver, #2 square bit, needle nose pliers
All of the information for this door boot seal replacement video is applicable to the following brands:
Electrolux
Tools needed: Phillips head screwdriver, #2 square bit, needle nose pliers
Step-By-Step Instructions
1
Before you replace the door boot seal in your washer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel to the support bracket.
5
Pull out the dispenser drawer and depress the button to fully release it.
6
You can now remove the remaining screws securing the control panel assembly.
7
Lift the assembly up to detach and disconnect the user interface wire connecter.
8
Use a flat-head screwdriver to help open the main control cover then disconnect the door latch wire harness.
9
Open the washer door and use needle-nose pliers to help remove the outer boot seal retainer.
10
Remove the boot seal from the lip of the front panel.
11
Lift and support the washer so you can unthread the bottom front panel mounting screws.
12
Remove the support and unthread the top front panel mounting screws.
13
Lift the panel up and out.
14
Remove the light from the boot seal.
15
Cut the zip tie securing the hose connecter and pull the connecter free of the boot.
16
Pull the bottom of the boot seal forward and push down to release the inner boot seal retainer spring.
17
Fully remove the old boot seal.
18
You’re now ready to install the new door boot seal.
19
Keeping the ports at the top, position the lip of the new seal behind the outer drum rim.
20
Once the seal is fully positioned, reinstall the inner boot retainer spring to secure – you can use a strong spring clamp to help hold the retainer spring in place as you install it.
21
We recommend using eye protection during this step.
22
With the seal secured, insert the light into the appropriate port.
23
Apply some dish soap to the hose connecter to make it easier to insert the connecter into the port.
24
Secure the connecter with a zip tie.
25
Reinstall the front panel by aligning it on the mounting pins.
26
Replace the mounting screws on top.
27
Lift and support the washer to replace the bottom mounting screws.
28
Now align the new boot seal on the lip of the front panel.
29
Secure the boot to the panel with the outer boot retainer.
30
Reconnect the door latch wire harness and close the main control cover.
31
Reinstall the control panel assembly by first reconnecting the user interface wire connecter.
32
Realign the panel on the support bracket and rethread all of the mounting screws.
33
Replace the dispenser drawer.
34
Realign the main top and slide it into place.
35
Rethread the screws in the back.
36
With the repair completed plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com