Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Washer Drain Pump Replacement #137240800
Electrolux Washer Drain Pump Replacement #137240800
Skill Level
Total Parts Cost
$159.03Estimated Savings
$112.5006:49
- Description
This video provides step-by-step repair instructions for replacing the drain pump on an Electrolux washing machine. The most common reason for replacing the drain pump is the washer not draining properly.
All of the information for this drain pump replacement video is applicable to the following brands:
Electrolux
Tools needed: phillips head screwdriver, #2 square bit, 5/16 inch socket, needle nose pliers, flat head screwdriver
All of the information for this drain pump replacement video is applicable to the following brands:
Electrolux
Tools needed: phillips head screwdriver, #2 square bit, 5/16 inch socket, needle nose pliers, flat head screwdriver
Step By Step Instructions
1
Before you replace the drain pump in your washer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel to the support bracket.
5
Pull out the dispenser and depress the button to fully release it.
6
You can now remove the remaining screws securing the control panel assembly.
7
Lift the assembly up to detach and disconnect the user interface wire connecter.
8
Use a flat-head screwdriver to help open the main control cover.
9
Disconnect the door latch wire harness.
10
Open the washer door and use needle-nose pliers to help remove the outer boot seal retainer.
11
Remove the boot seal from the lip of the front panel.
12
Lift and support the washer so you can unthread the bottom front panel mounting screws.
13
Remove the support and unthread the top front panel mounting screws.
14
Lift the panel up and out.
15
Disconnect the drain pump wire connecter – you may have to slide the pump cover off and use a flat-head screwdriver to help lift up the cover to disconnect the wire.
16
Next, release the spring clamps securing the inlet and drain hoses to the pump and pull both hoses off – be prepared for some water to spill.
17
Use a 5/16th inch socket or the phillips-head screwdriver to unthread the drain pump mounting screw.
18
You can now detach the old pump from the rubber mount.
19
Install the new drain pump by inserting the support tabs into the rubber mount.
20
Thread the mounting screw to secure.
21
Attach the inlet and drain hoses to the appropriate ports and secure with the spring clamps.
22
Connect the wire connecter.
23
Reinstall the front panel by aligning it on the mounting pins.
24
Replace the mounting screws on top.
25
Lift and support the washer to replace the bottom mounting screws.
26
Now realign the boot seal on the lip of the front panel.
27
Secure the boot to the panel with the outer boot retainer.
28
Reconnect the door latch wire harness and close the main control cover.
29
Reinstall the control panel assembly by first reconnecting the user interface wire connecter.
30
Realign the panel on the support bracket and rethread all of the mounting screws.
31
Replace the dispenser.
32
Realign the main top and slide it into place.
33
Rethread the screws in the back.
34
With the repair completed plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the drain pump on an Electrolux washing machine. The most common reason for replacing the drain pump is the washer not draining properly.
All of the information for this drain pump replacement video is applicable to the following brands:
Electrolux
Tools needed: phillips head screwdriver, #2 square bit, 5/16 inch socket, needle nose pliers, flat head screwdriver
All of the information for this drain pump replacement video is applicable to the following brands:
Electrolux
Tools needed: phillips head screwdriver, #2 square bit, 5/16 inch socket, needle nose pliers, flat head screwdriver
Step-By-Step Instructions
1
Before you replace the drain pump in your washer be sure to unplug the power cord.
2
Use a number two square bit or a phillips-head screwdriver to unthread the screws at the back securing the main top.
3
Slide the main top back and lift it up to remove.
4
Next, unthread the screws securing the control panel to the support bracket.
5
Pull out the dispenser and depress the button to fully release it.
6
You can now remove the remaining screws securing the control panel assembly.
7
Lift the assembly up to detach and disconnect the user interface wire connecter.
8
Use a flat-head screwdriver to help open the main control cover.
9
Disconnect the door latch wire harness.
10
Open the washer door and use needle-nose pliers to help remove the outer boot seal retainer.
11
Remove the boot seal from the lip of the front panel.
12
Lift and support the washer so you can unthread the bottom front panel mounting screws.
13
Remove the support and unthread the top front panel mounting screws.
14
Lift the panel up and out.
15
Disconnect the drain pump wire connecter – you may have to slide the pump cover off and use a flat-head screwdriver to help lift up the cover to disconnect the wire.
16
Next, release the spring clamps securing the inlet and drain hoses to the pump and pull both hoses off – be prepared for some water to spill.
17
Use a 5/16th inch socket or the phillips-head screwdriver to unthread the drain pump mounting screw.
18
You can now detach the old pump from the rubber mount.
19
Install the new drain pump by inserting the support tabs into the rubber mount.
20
Thread the mounting screw to secure.
21
Attach the inlet and drain hoses to the appropriate ports and secure with the spring clamps.
22
Connect the wire connecter.
23
Reinstall the front panel by aligning it on the mounting pins.
24
Replace the mounting screws on top.
25
Lift and support the washer to replace the bottom mounting screws.
26
Now realign the boot seal on the lip of the front panel.
27
Secure the boot to the panel with the outer boot retainer.
28
Reconnect the door latch wire harness and close the main control cover.
29
Reinstall the control panel assembly by first reconnecting the user interface wire connecter.
30
Realign the panel on the support bracket and rethread all of the mounting screws.
31
Replace the dispenser.
32
Realign the main top and slide it into place.
33
Rethread the screws in the back.
34
With the repair completed plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com