Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Gas Range Oven Control Panel Replacement #W10585590
Whirlpool Gas Range Oven Control Panel Replacement #W10585590
Skill Level
Total Parts Cost
$163.84Estimated Savings
$112.5003:49
- Description
This video provides step-by-step instructions for replacing the oven control panel on a Whirlpool gas range. The most common reason for replacing the panel is if it is damaged.
All of the information in this panel replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Tools used: phillips head screwdriver
All of the information in this panel replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Tools used: phillips head screwdriver
Step By Step Instructions
1
Before you replace the oven control panel in your range unplug the power cord.
2
Use a phillips-head screwdriver to unthread the screws securing the upper rear access panel.
3
Lift the panel up and out to remove.
4
Note the orientation of the wire harness connecters then disconnect them from the control board.
5
Set the insulation aside and unthread the control board mounting screws.
6
With the screws unthreaded, pull the board away from the control panel.
7
Next, remove the two screws at the top securing the control panel.
8
Use a short phillips-head screwdriver to unthread the screws securing the bottom of the panel.
9
Lift the bottom of the old control panel up to remove.
10
Prepare the new oven control panel for installation by transferring the support brackets from the old panel to the new one.
11
Now remove the protective film.
12
Align the new panel on the frame then replace the screws to secure the bottom of the panel.
13
Thread and tighten the screws at the top.
14
Align the control board on the new panel then replace the mounting screws to secure.
15
Connect the wire harness connecters.
16
Replace the insulation.
17
Reinstall the access panel by inserting the tabs into the slots.
18
Thread and tighten the screws to secure.
19
With the repair completed plug the power cord back in and your range should be ready for use.
Description
This video provides step-by-step instructions for replacing the oven control panel on a Whirlpool gas range. The most common reason for replacing the panel is if it is damaged.
All of the information in this panel replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Tools used: phillips head screwdriver
All of the information in this panel replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Tools used: phillips head screwdriver
Step-By-Step Instructions
1
Before you replace the oven control panel in your range unplug the power cord.
2
Use a phillips-head screwdriver to unthread the screws securing the upper rear access panel.
3
Lift the panel up and out to remove.
4
Note the orientation of the wire harness connecters then disconnect them from the control board.
5
Set the insulation aside and unthread the control board mounting screws.
6
With the screws unthreaded, pull the board away from the control panel.
7
Next, remove the two screws at the top securing the control panel.
8
Use a short phillips-head screwdriver to unthread the screws securing the bottom of the panel.
9
Lift the bottom of the old control panel up to remove.
10
Prepare the new oven control panel for installation by transferring the support brackets from the old panel to the new one.
11
Now remove the protective film.
12
Align the new panel on the frame then replace the screws to secure the bottom of the panel.
13
Thread and tighten the screws at the top.
14
Align the control board on the new panel then replace the mounting screws to secure.
15
Connect the wire harness connecters.
16
Replace the insulation.
17
Reinstall the access panel by inserting the tabs into the slots.
18
Thread and tighten the screws to secure.
19
With the repair completed plug the power cord back in and your range should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com