Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Gas Range Power Cord Replacement #W10640762
Whirlpool Gas Range Power Cord Replacement #W10640762
Skill Level
Total Parts Cost
$79.23Estimated Savings
$112.5003:52
- Description
This video provides step-by-step instructions for replacing the power cord on a Whirlpool gas range. The most common reason for replacing the power cord is if nothing is working on the range and the control board is not at fault; the power cord is only very rarely defective.
All of the information in this power cord replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Tools used: phillips head screwdriver, 5/16 inch socket or nut driver, pliers, flat head screwdriver
All of the information in this power cord replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Tools used: phillips head screwdriver, 5/16 inch socket or nut driver, pliers, flat head screwdriver
Step By Step Instructions
1
Before you replace the power cord on your range make sure the old cord is unplugged.
2
Lift up the left side of the range and support it.
3
Use a phillips-head screwdriver to unthread the screws securing the bottom of the left side panel.
4
With the screws unthreaded, remove the support and lower the appliance.
5
Now remove the screws securing the support braces to the side panel.
6
Unthread the lower mounting screw.
7
Unthread the screws securing the spark module cover to the side panel.
8
Pull the side panel out, being careful not to bend it, and prop it open.
9
Using a 5/16th inch socket or nut driver, unthread the screw to release the power cord grounding wire.
10
Disconnect the power cord wire harness.
11
Use pliers to depress the tabs to release the power cord strain relief and a flat-head screwdriver to pry the old cord free.
12
Install the new power cord by inserting the wire connecter through the hole in the rear panel and snapping the strain relief into place.
13
Connect the wire harness.
14
Remove the support and reposition the side panel.
15
Secure the lower mounting screw.
16
Position the grounding wire and secure it with the screw.
17
Rethread the screws to secure the spark module cover to the side panel.
18
Realign the support braces and secure the screws.
19
Lift the range up and support it then thread and tighten the screws to secure the bottom of the side panel.
20
Remove the support and lower the appliance.
21
With the repair completed plug the new power cord in and your range should be ready for use.
Description
This video provides step-by-step instructions for replacing the power cord on a Whirlpool gas range. The most common reason for replacing the power cord is if nothing is working on the range and the control board is not at fault; the power cord is only very rarely defective.
All of the information in this power cord replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Tools used: phillips head screwdriver, 5/16 inch socket or nut driver, pliers, flat head screwdriver
All of the information in this power cord replacement video is applicable to the following brands: Maytag, Amana, Magic Chef, Whirlpool, Tappan, Estate, Kitchenaide
Tools used: phillips head screwdriver, 5/16 inch socket or nut driver, pliers, flat head screwdriver
Step-By-Step Instructions
1
Before you replace the power cord on your range make sure the old cord is unplugged.
2
Lift up the left side of the range and support it.
3
Use a phillips-head screwdriver to unthread the screws securing the bottom of the left side panel.
4
With the screws unthreaded, remove the support and lower the appliance.
5
Now remove the screws securing the support braces to the side panel.
6
Unthread the lower mounting screw.
7
Unthread the screws securing the spark module cover to the side panel.
8
Pull the side panel out, being careful not to bend it, and prop it open.
9
Using a 5/16th inch socket or nut driver, unthread the screw to release the power cord grounding wire.
10
Disconnect the power cord wire harness.
11
Use pliers to depress the tabs to release the power cord strain relief and a flat-head screwdriver to pry the old cord free.
12
Install the new power cord by inserting the wire connecter through the hole in the rear panel and snapping the strain relief into place.
13
Connect the wire harness.
14
Remove the support and reposition the side panel.
15
Secure the lower mounting screw.
16
Position the grounding wire and secure it with the screw.
17
Rethread the screws to secure the spark module cover to the side panel.
18
Realign the support braces and secure the screws.
19
Lift the range up and support it then thread and tighten the screws to secure the bottom of the side panel.
20
Remove the support and lower the appliance.
21
With the repair completed plug the new power cord in and your range should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com