Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Electric Dryer Idler Pulley Spring #WPW10446781
Whirlpool Electric Dryer Idler Pulley Spring #WPW10446781
Skill Level
Total Parts Cost
$24.77Estimated Savings
$112.5007:35
- Description
This video provides step-by-step repair instructions for replacing the idler pulley spring on a Whirlpool electric dryer. The most common reason for replacing the idler spring is if it is damaged.
This idler pulley spring replacement video is applicable to the following brands:
Whirlpool, Admiral, Amana, Crosley, Inglis, Kenmore, KitchenAid, Maytag
Tools needed: 5/16th inch socket or nut driver, quarter-inch socket or nut driver
Don't forget to like and comment on this video and subscribe to our channel!
This idler pulley spring replacement video is applicable to the following brands:
Whirlpool, Admiral, Amana, Crosley, Inglis, Kenmore, KitchenAid, Maytag
Tools needed: 5/16th inch socket or nut driver, quarter-inch socket or nut driver
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace the idler pulley spring in your dryer be sure to unplug the power cord.
2
Use a 5/16th inch socket or nut driver to unthread the rear screws securing the top panel.
3
Slide the top panel back and lift up to detach.
4
Use a quarter-inch socket or nut driver to unthread the control panel housing mounting screws.
5
Disconnect the control panel wire connecter from the main control board.
6
Lift up the tabs to detach the housing.
7
Disconnect the door switch wire connecter.
8
Now lift up the front of the dryer and support it then use the quarter-inch socket or nut driver to remove the four lower mounting screws securing the front panel.
9
Remove the support and lower the appliance.
10
Open the dryer door and use a phillips-head screwdriver to unthread the screws securing the front panel to the bulkhead.
11
Using the quarter-inch socket or nut driver, unthread the upper mounting screws.
12
You can now lift the front panel up to detach it from the cabinet.
13
Use the quarter-inch socket or nut driver to unthread the screw securing the control board support bracket.
14
Use wire or string to secure the support
15
Next, remove the screws securing the front support brace.
16
Detach the brace.
17
Unthread the screw to release the lower support bracket.
18
Remove the front bulkhead mounting screws.
19
Disconnect the sensor wire connecter.
20
You can now remove the front bulkhead.
21
Reach under the drum and unthread the belt from the pulley and motor shaft.
22
You can use the belt to help lift out the drum.
23
Lift the idler pulley arm up and use needle-nose pliers to detach the old spring.
24
Install the new idler pulley spring by hooking the large end onto the motor mount and the smaller end onto the pulley arm.
25
Reinstall the drum by aligning the rear of the drum on the rollers – the rear of the drum has a larger bevel.
26
Loop the belt on the pulley and motor shaft in a zig-zag formation.
27
Rotate the drum to help align the belt.
28
Reposition the front bulkhead on the drum then hook it onto the cabinet tabs.
29
Reconnect the sensor wire connecter and rethread the mounting screws to secure the bulkhead.
30
Realign the lower support bracket and secure it with the screw.
31
Reposition the front support brace.
32
Rethread the screws.
33
Align the control board support bracket and replace the screw.
34
Reinstall the front panel by first feeding the door switch wire harness under the support brace then align the panel on the cabinet tabs.
35
Rethread the upper mounting screws.
36
Support the front of the dryer to replace the lower screws.
37
Secure the two screws behind the door as well.
38
Connect the door switch wire connecter.
39
Insert the control panel housing tabs into the slots in the front panel and snap the housing into place.
40
Rethread the mounting screws.
41
Connect the wire connecter to the main control board.
42
Realign the top panel and slide it into position.
43
Secure the screws.
44
With the repair completed plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the idler pulley spring on a Whirlpool electric dryer. The most common reason for replacing the idler spring is if it is damaged.
This idler pulley spring replacement video is applicable to the following brands:
Whirlpool, Admiral, Amana, Crosley, Inglis, Kenmore, KitchenAid, Maytag
Tools needed: 5/16th inch socket or nut driver, quarter-inch socket or nut driver
Don't forget to like and comment on this video and subscribe to our channel!
This idler pulley spring replacement video is applicable to the following brands:
Whirlpool, Admiral, Amana, Crosley, Inglis, Kenmore, KitchenAid, Maytag
Tools needed: 5/16th inch socket or nut driver, quarter-inch socket or nut driver
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace the idler pulley spring in your dryer be sure to unplug the power cord.
2
Use a 5/16th inch socket or nut driver to unthread the rear screws securing the top panel.
3
Slide the top panel back and lift up to detach.
4
Use a quarter-inch socket or nut driver to unthread the control panel housing mounting screws.
5
Disconnect the control panel wire connecter from the main control board.
6
Lift up the tabs to detach the housing.
7
Disconnect the door switch wire connecter.
8
Now lift up the front of the dryer and support it then use the quarter-inch socket or nut driver to remove the four lower mounting screws securing the front panel.
9
Remove the support and lower the appliance.
10
Open the dryer door and use a phillips-head screwdriver to unthread the screws securing the front panel to the bulkhead.
11
Using the quarter-inch socket or nut driver, unthread the upper mounting screws.
12
You can now lift the front panel up to detach it from the cabinet.
13
Use the quarter-inch socket or nut driver to unthread the screw securing the control board support bracket.
14
Use wire or string to secure the support
15
Next, remove the screws securing the front support brace.
16
Detach the brace.
17
Unthread the screw to release the lower support bracket.
18
Remove the front bulkhead mounting screws.
19
Disconnect the sensor wire connecter.
20
You can now remove the front bulkhead.
21
Reach under the drum and unthread the belt from the pulley and motor shaft.
22
You can use the belt to help lift out the drum.
23
Lift the idler pulley arm up and use needle-nose pliers to detach the old spring.
24
Install the new idler pulley spring by hooking the large end onto the motor mount and the smaller end onto the pulley arm.
25
Reinstall the drum by aligning the rear of the drum on the rollers – the rear of the drum has a larger bevel.
26
Loop the belt on the pulley and motor shaft in a zig-zag formation.
27
Rotate the drum to help align the belt.
28
Reposition the front bulkhead on the drum then hook it onto the cabinet tabs.
29
Reconnect the sensor wire connecter and rethread the mounting screws to secure the bulkhead.
30
Realign the lower support bracket and secure it with the screw.
31
Reposition the front support brace.
32
Rethread the screws.
33
Align the control board support bracket and replace the screw.
34
Reinstall the front panel by first feeding the door switch wire harness under the support brace then align the panel on the cabinet tabs.
35
Rethread the upper mounting screws.
36
Support the front of the dryer to replace the lower screws.
37
Secure the two screws behind the door as well.
38
Connect the door switch wire connecter.
39
Insert the control panel housing tabs into the slots in the front panel and snap the housing into place.
40
Rethread the mounting screws.
41
Connect the wire connecter to the main control board.
42
Realign the top panel and slide it into position.
43
Secure the screws.
44
With the repair completed plug the power cord back in and your dryer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com