Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairMaytag Dryer Drum Roller Axle Replacement #WP40113601
Maytag Dryer Drum Roller Axle Replacement #WP40113601
Skill Level
Total Parts Cost
$54.24Estimated Savings
$112.5005:58
- Description
This video provides step-by-step instructions for replacing the drum roller axle on Maytag dryers. The most common reasons for replacing the roller axle are when the dryer makes noise, stops turning during a cycle, or the drum won’t turn at all.
All of the information in this roller axle replacement video is applicable to the following brands: Maytag, Jenn Air, Crosley
Tools used: 5/16" nut driver, snap ring pliers
All of the information in this roller axle replacement video is applicable to the following brands: Maytag, Jenn Air, Crosley
Tools used: 5/16" nut driver, snap ring pliers
Step By Step Instructions
1
Before you replace a drum roller axle in your dryer be sure to unplug the power cord.
2
Use a 5/16th inch socket or nut driver to unthread the screws securing the lower access panel.
3
Detach the panel.
4
Next, unthread the screws securing the bottom of the front panel.
5
Pull the panel out from the bottom to detach.
6
Note the orientation of the door switch wires then disconnect them and set the panel aside.
7
Unthread the main top mounting screws.
8
Lift the main top up and support it.
9
Disconnect the light assembly wires and remove them from the retainer.
10
Unthread the front bulkhead mounting screws.
11
Lift the bulkhead up to detach it from the cabinet.
12
Reach under the drum and unhook the belt from the pulley and the motor shaft.
13
You can use the belt to help lift out the drum.
14
Use snap-ring pliers to remove the snap ring securing the drum roller on the axle you’re replacing.
15
Slide off the front washer and the roller.
16
Remove the rear washer.
17
Use the 5/16th inch socket or nut driver to unthread the axle mounting screws to release the old axle.
18
Before you install the new drum roller axle file down any burrs found around the edge of the axle so the roller will slide on.
19
Align the axle on the rear bulkhead then thread the mounting screws to secure.
20
With the rear washer in place, note the designation for the front of the roller then slide the roller on the axle followed by the front washer.
21
Secure the roller with the snap ring.
22
Reinstall the drum by aligning it on the rollers.
23
Loop the belt on the pulley and motor shaft in a zigzag formation.
24
Rotate the drum to help align the belt.
25
Replace the front bulkhead ..by aligning the drum then insert the tabs into the slots in the cabinet.
26
Rethread the mounting screws.
27
Feed the light assembly wires through the retainer and reconnect them.
28
Remove the support and lower the main top.
29
Secure it with the screws.
30
Replace the front panel by first reconnecting the door switch wires to the appropriate terminals.
31
Now hook the retaining clips under the main top fully reposition the panel and rethread the screws at the bottom.
32
Realign the lower access panel and secure it with the screws.
33
With the repair completed plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step instructions for replacing the drum roller axle on Maytag dryers. The most common reasons for replacing the roller axle are when the dryer makes noise, stops turning during a cycle, or the drum won’t turn at all.
All of the information in this roller axle replacement video is applicable to the following brands: Maytag, Jenn Air, Crosley
Tools used: 5/16" nut driver, snap ring pliers
All of the information in this roller axle replacement video is applicable to the following brands: Maytag, Jenn Air, Crosley
Tools used: 5/16" nut driver, snap ring pliers
Step-By-Step Instructions
1
Before you replace a drum roller axle in your dryer be sure to unplug the power cord.
2
Use a 5/16th inch socket or nut driver to unthread the screws securing the lower access panel.
3
Detach the panel.
4
Next, unthread the screws securing the bottom of the front panel.
5
Pull the panel out from the bottom to detach.
6
Note the orientation of the door switch wires then disconnect them and set the panel aside.
7
Unthread the main top mounting screws.
8
Lift the main top up and support it.
9
Disconnect the light assembly wires and remove them from the retainer.
10
Unthread the front bulkhead mounting screws.
11
Lift the bulkhead up to detach it from the cabinet.
12
Reach under the drum and unhook the belt from the pulley and the motor shaft.
13
You can use the belt to help lift out the drum.
14
Use snap-ring pliers to remove the snap ring securing the drum roller on the axle you’re replacing.
15
Slide off the front washer and the roller.
16
Remove the rear washer.
17
Use the 5/16th inch socket or nut driver to unthread the axle mounting screws to release the old axle.
18
Before you install the new drum roller axle file down any burrs found around the edge of the axle so the roller will slide on.
19
Align the axle on the rear bulkhead then thread the mounting screws to secure.
20
With the rear washer in place, note the designation for the front of the roller then slide the roller on the axle followed by the front washer.
21
Secure the roller with the snap ring.
22
Reinstall the drum by aligning it on the rollers.
23
Loop the belt on the pulley and motor shaft in a zigzag formation.
24
Rotate the drum to help align the belt.
25
Replace the front bulkhead ..by aligning the drum then insert the tabs into the slots in the cabinet.
26
Rethread the mounting screws.
27
Feed the light assembly wires through the retainer and reconnect them.
28
Remove the support and lower the main top.
29
Secure it with the screws.
30
Replace the front panel by first reconnecting the door switch wires to the appropriate terminals.
31
Now hook the retaining clips under the main top fully reposition the panel and rethread the screws at the bottom.
32
Realign the lower access panel and secure it with the screws.
33
With the repair completed plug the power cord back in and your dryer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com