Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKenmore Top Load Washer Pressure Switch Assembly #W10337780
Kenmore Top Load Washer Pressure Switch Assembly #W10337780
Skill Level
Total Parts Cost
$62.45Estimated Savings
$112.5004:15
- Description
This video provides step-by-step repair instructions for replacing the pressure switch assembly on a Kenmore Top-Load washing machine. The most common reason for replacing the pressure switch is if the washer is under-filling or not running.
All of the information for this pressure switch replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers
All of the information for this pressure switch replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers
Step By Step Instructions
1
Before you replace the pressure switch assembly in your washer, be sure to unplug the power cord.
2
Detach the two control panel end caps by pulling them off from the top.
3
Use a Phillips head screwdriver to unthread the two screws securing the control panel.
4
Remove the water level selector knob and lift up the control panel.
5
Next, disconnect the lid switch wire connector using a flathead screwdriver.
6
Release the spring clips securing the cabinet to the rear panel.
7
Tilt the cabinet toward you, slide forward, and remove.
8
Detach the pressure tube from the air dome.
9
Pull it out of the retainers and the retaining clip.
10
Now, release the retaining tab and rotate the pressure switch to detach it from the control panel.
11
Disconnect the wire connector to fully remove the old switch.
12
Prepare the new pressure switch assembly for installation by first trimming the pressure tube to the proper length.
13
Slide the clamp onto the tube, attach the tube to the pressure switch, and secure it with the clamp.
14
Connect the wire connector to the new switch.
15
Now, align the switch in the control panel and rotate to lock it into place.
16
Feed the pressure tube under the retaining clip and through the retainers.
17
Then, attach the tube to the air dome.
18
Reinstall the cap net by sliding the front edge of the cabinet underneath the base frame.
19
Use your foot to push it into position.
20
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
21
Make sure the sides of the cabinet are properly aligned with the rear panel.
22
Reinstall the spring clips to secure the cabinet.
23
Reconnect the lid switch wire connector.
24
Lower the control panel and snap the retaining clips into the slots in the main top.
25
Align the knob on the new switch stem.
26
Re-thread and tighten the screws to secure the control panel.
27
Realign the end caps and snap them into place.
28
With the repair completed, plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the pressure switch assembly on a Kenmore Top-Load washing machine. The most common reason for replacing the pressure switch is if the washer is under-filling or not running.
All of the information for this pressure switch replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers
All of the information for this pressure switch replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers
Step-By-Step Instructions
1
Before you replace the pressure switch assembly in your washer, be sure to unplug the power cord.
2
Detach the two control panel end caps by pulling them off from the top.
3
Use a Phillips head screwdriver to unthread the two screws securing the control panel.
4
Remove the water level selector knob and lift up the control panel.
5
Next, disconnect the lid switch wire connector using a flathead screwdriver.
6
Release the spring clips securing the cabinet to the rear panel.
7
Tilt the cabinet toward you, slide forward, and remove.
8
Detach the pressure tube from the air dome.
9
Pull it out of the retainers and the retaining clip.
10
Now, release the retaining tab and rotate the pressure switch to detach it from the control panel.
11
Disconnect the wire connector to fully remove the old switch.
12
Prepare the new pressure switch assembly for installation by first trimming the pressure tube to the proper length.
13
Slide the clamp onto the tube, attach the tube to the pressure switch, and secure it with the clamp.
14
Connect the wire connector to the new switch.
15
Now, align the switch in the control panel and rotate to lock it into place.
16
Feed the pressure tube under the retaining clip and through the retainers.
17
Then, attach the tube to the air dome.
18
Reinstall the cap net by sliding the front edge of the cabinet underneath the base frame.
19
Use your foot to push it into position.
20
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
21
Make sure the sides of the cabinet are properly aligned with the rear panel.
22
Reinstall the spring clips to secure the cabinet.
23
Reconnect the lid switch wire connector.
24
Lower the control panel and snap the retaining clips into the slots in the main top.
25
Align the knob on the new switch stem.
26
Re-thread and tighten the screws to secure the control panel.
27
Realign the end caps and snap them into place.
28
With the repair completed, plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com