Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKenmore Top-Load Washer Basket Drive Kit Replacement W10820043
Kenmore Top-Load Washer Basket Drive Kit Replacement W10820043
Skill Level
Total Parts Cost
$169.35Estimated Savings
$112.5010:49
- Description
This video provides step-by-step repair instructions for replacing the basket drive kit on a Kenmore Top-Load washing machine. The most common reason for replacing the basket drive is if the tub is not spinning or agitating.
All of the information for this basket drive kit replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers, spanner wrench, hammer, 1/2" square drive, 9/16" deep well socket, 1/4" nut driver, 1/2" socket
All of the information for this basket drive kit replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers, spanner wrench, hammer, 1/2" square drive, 9/16" deep well socket, 1/4" nut driver, 1/2" socket
Step By Step Instructions
1
Before you replace the basket drive in your washer be sure to unplug the power cord
2
Shut off the water supply valves.
3
Use pliers to help remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
4
Release the retaining clamp and pull the drain hose off of the coupler and set the hose aside.
5
Detach the two control panel end caps by pulling them off from the top.
6
Use a phillips-head screwdriver to unthread the two screws securing the control panel.
7
Lift up the control panel.
8
Next, disconnect the lid switch wire connecter.
9
Using a flat-head screwdriver, release the spring clips securing the cabinet to the rear panel.
10
Tilt the cabinet toward you, slide forward and remove.
11
Release the retaining tabs to detach the fill spout from the rear panel.
12
Detach the hose from the bleach dispenser and release the tabs securing the tub ring.
13
Remove the tub ring.
14
Next, remove the fabric softener dispenser or agitator cap.
15
Lift out the cover and use a half-inch square drive to unthread the agitator retainer.
16
With the retainer loosened, you can lift off the upper agitator.
17
Remove the bushing and use a 9/16th inch deep-well socket to unthread the bolt securing the lower agitator.
18
Remove the agitator.
19
Lift the spacer and the plastic washer off of the transmission shaft.
20
Use a spanner wrench and hammer to loosen the tub nut by rotating it counter-clockwise.
21
Unthread the nut.
22
You can now lift out the inner tub.
23
Remove the drive block.
24
Next, release the drain pump retaining clips and pull the pump off the motor shaft.
25
Disconnect the motor wire connecters.
26
To make the procedure easier, we recommend uninstalling the motor.
27
Use a quarter-inch socket or nut driver to unthread the mounting screws.
28
Release the bottom mounting clip support the motor then release the top mounting clip and set the motor aside.
29
Now carefully tip the appliance back and rest it on a towel or blanket.
30
Detach the wire retainer from the transmission housing.
31
Use a half-inch socket to unthread the mounting bolts securing the transmission.
32
Slide the transmission out.
33
Turn the brake lever counter-clockwise and you can pull out the old basket drive.
34
Prepare to install the new basket drive by referring to the instructions to determine the proper spring and clutch components for your model.
35
Fully insert the new basket drive into the bottom of the outer tub.
36
If worn, remove the old clutch band.
37
Prepare the new clutch band by hooking the appropriate spring on the tabs then insert the band into the clutch housing.
38
Make sure the thrust washer is in place on the transmission shaft then reinstall the transmission.
39
Thread and tighten the mounting bolts to secure.
40
Snap the wire retainer into place.
41
Return the washer to its upright position.
42
Before you reinstall the drive motor, inspect the coupler for damage and replace if necessary.
43
Now line up the prongs on the coupler cog with the holes in the isolator then slide the motor into position.
44
Reposition the mounting clips and snap them into place.
45
Rethread and tighten the screws.
46
Reconnect the motor wire connecters.
47
Realign the drain pump on the motor shaft and secure the pump with the retaining clips.
48
Reseat the drive block on the transmission shaft.
49
Now align the inner tub on the drive block.
50
Thread the tub nut clockwise.
51
Use the spanner wrench and hammer to tighten.
52
Realign the plastic washer and the spacer.
53
Reposition the lower agitator.
54
Thread and tighten the bolt to secure.
55
Replace the bushing.
56
Realign the upper agitator and insert the cam and cog assembly into the agitator.
57
Insert the retainer and spring then use the half-inch square drive to tighten.
58
Align the cover and snap on the dispenser or cap.
59
Realign the tub ring on the outer tub and snap it into place.
60
Secure the hose to the bleach dispenser.
61
Reattach the fill spout to the rear panel.
62
Reinstall the cabinet by sliding the front edge of the cabinet underneath the base frame.
63
Use your foot to push it into position.
64
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
65
Make sure the sides of the cabinet are properly aligned with the rear panel.
66
Reinstall the spring clips to secure the cabinet.
67
Reconnect the lid switch wire connecter.
68
Lower the control panel and snap the retaining clips into the slots in the main top.
69
Rethread and tighten the screws to secure the control panel.
70
Realign the end caps and snap them into place.
71
Reattach the drain hose to the coupler and secure it with the clamp.
72
Reattach the hot and cold water supply lines to the inlet valve.
73
With the repair completed turn the water supply back on plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the basket drive kit on a Kenmore Top-Load washing machine. The most common reason for replacing the basket drive is if the tub is not spinning or agitating.
All of the information for this basket drive kit replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers, spanner wrench, hammer, 1/2" square drive, 9/16" deep well socket, 1/4" nut driver, 1/2" socket
All of the information for this basket drive kit replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers, spanner wrench, hammer, 1/2" square drive, 9/16" deep well socket, 1/4" nut driver, 1/2" socket
Step-By-Step Instructions
1
Before you replace the basket drive in your washer be sure to unplug the power cord
2
Shut off the water supply valves.
3
Use pliers to help remove the hot and cold water supply lines from the inlet valve – be prepared for some water to spill out.
4
Release the retaining clamp and pull the drain hose off of the coupler and set the hose aside.
5
Detach the two control panel end caps by pulling them off from the top.
6
Use a phillips-head screwdriver to unthread the two screws securing the control panel.
7
Lift up the control panel.
8
Next, disconnect the lid switch wire connecter.
9
Using a flat-head screwdriver, release the spring clips securing the cabinet to the rear panel.
10
Tilt the cabinet toward you, slide forward and remove.
11
Release the retaining tabs to detach the fill spout from the rear panel.
12
Detach the hose from the bleach dispenser and release the tabs securing the tub ring.
13
Remove the tub ring.
14
Next, remove the fabric softener dispenser or agitator cap.
15
Lift out the cover and use a half-inch square drive to unthread the agitator retainer.
16
With the retainer loosened, you can lift off the upper agitator.
17
Remove the bushing and use a 9/16th inch deep-well socket to unthread the bolt securing the lower agitator.
18
Remove the agitator.
19
Lift the spacer and the plastic washer off of the transmission shaft.
20
Use a spanner wrench and hammer to loosen the tub nut by rotating it counter-clockwise.
21
Unthread the nut.
22
You can now lift out the inner tub.
23
Remove the drive block.
24
Next, release the drain pump retaining clips and pull the pump off the motor shaft.
25
Disconnect the motor wire connecters.
26
To make the procedure easier, we recommend uninstalling the motor.
27
Use a quarter-inch socket or nut driver to unthread the mounting screws.
28
Release the bottom mounting clip support the motor then release the top mounting clip and set the motor aside.
29
Now carefully tip the appliance back and rest it on a towel or blanket.
30
Detach the wire retainer from the transmission housing.
31
Use a half-inch socket to unthread the mounting bolts securing the transmission.
32
Slide the transmission out.
33
Turn the brake lever counter-clockwise and you can pull out the old basket drive.
34
Prepare to install the new basket drive by referring to the instructions to determine the proper spring and clutch components for your model.
35
Fully insert the new basket drive into the bottom of the outer tub.
36
If worn, remove the old clutch band.
37
Prepare the new clutch band by hooking the appropriate spring on the tabs then insert the band into the clutch housing.
38
Make sure the thrust washer is in place on the transmission shaft then reinstall the transmission.
39
Thread and tighten the mounting bolts to secure.
40
Snap the wire retainer into place.
41
Return the washer to its upright position.
42
Before you reinstall the drive motor, inspect the coupler for damage and replace if necessary.
43
Now line up the prongs on the coupler cog with the holes in the isolator then slide the motor into position.
44
Reposition the mounting clips and snap them into place.
45
Rethread and tighten the screws.
46
Reconnect the motor wire connecters.
47
Realign the drain pump on the motor shaft and secure the pump with the retaining clips.
48
Reseat the drive block on the transmission shaft.
49
Now align the inner tub on the drive block.
50
Thread the tub nut clockwise.
51
Use the spanner wrench and hammer to tighten.
52
Realign the plastic washer and the spacer.
53
Reposition the lower agitator.
54
Thread and tighten the bolt to secure.
55
Replace the bushing.
56
Realign the upper agitator and insert the cam and cog assembly into the agitator.
57
Insert the retainer and spring then use the half-inch square drive to tighten.
58
Align the cover and snap on the dispenser or cap.
59
Realign the tub ring on the outer tub and snap it into place.
60
Secure the hose to the bleach dispenser.
61
Reattach the fill spout to the rear panel.
62
Reinstall the cabinet by sliding the front edge of the cabinet underneath the base frame.
63
Use your foot to push it into position.
64
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
65
Make sure the sides of the cabinet are properly aligned with the rear panel.
66
Reinstall the spring clips to secure the cabinet.
67
Reconnect the lid switch wire connecter.
68
Lower the control panel and snap the retaining clips into the slots in the main top.
69
Rethread and tighten the screws to secure the control panel.
70
Realign the end caps and snap them into place.
71
Reattach the drain hose to the coupler and secure it with the clamp.
72
Reattach the hot and cold water supply lines to the inlet valve.
73
With the repair completed turn the water supply back on plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com