Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKenmore Top-Load Washer Valve Outlet Hose #WP3349365
Kenmore Top-Load Washer Valve Outlet Hose #WP3349365
Skill Level
Total Parts Cost
$13.46Estimated Savings
$112.5003:31
- Description
This video provides step-by-step repair instructions for replacing the valve outlet hose on a Kenmore Top-Load washing machine. The most common reason for replacing the hose is if the washing machine is leaking.
All of the information for this valve outlet hose replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers
All of the information for this valve outlet hose replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers
Step By Step Instructions
1
Before you replace the valve outlet hose in your washer be sure to unplug the power cord.
2
Detach the two control panel end caps by pulling them off from the top.
3
Use a phillips-head screwdriver to unthread the two screws securing the control panel.
4
Lift up the control panel.
5
Next, disconnect the lid switch wire connecter.
6
Using a flat-head screwdriver, release the spring clips securing the cabinet to the rear panel.
7
Tilt the cabinet toward you, slide forward and remove.
8
Use pliers to release the retaining clamps securing the valve outlet hose to the fill spout and the thermistor then pull the old hose free.
9
Remove the larger retaining clamp from the hose and leave the smaller clamp resting on the thermistor.
10
Install the new valve outlet hose by sliding the large retaining clamp over the larger end of the hose.
11
Attach that end to the fill spout and secure it with the clamp.
12
Attach the opposite end to the thermistor and use the clamp to secure.
13
Reinstall the cabinet by sliding the front edge of the cabinet underneath the base frame.
14
Use your foot to push it into position.
15
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
16
Make sure the sides of the cabinet are properly aligned with the rear panel.
17
Reinstall the spring clips to secure the cabinet.
18
Reconnect the lid switch wire connecter.
19
Lower the control panel and snap the retaining clips into the slots in the main top.
20
Rethread and tighten the screws to secure the control panel.
21
Realign the end caps and snap them into place.
22
With the repair completed plug the power cord back in and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the valve outlet hose on a Kenmore Top-Load washing machine. The most common reason for replacing the hose is if the washing machine is leaking.
All of the information for this valve outlet hose replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers
All of the information for this valve outlet hose replacement video is applicable to the following brands:
Kenmore, Whirlpool
Tools used: Phillips-head screwdriver, flat-head screwdriver, pliers
Step-By-Step Instructions
1
Before you replace the valve outlet hose in your washer be sure to unplug the power cord.
2
Detach the two control panel end caps by pulling them off from the top.
3
Use a phillips-head screwdriver to unthread the two screws securing the control panel.
4
Lift up the control panel.
5
Next, disconnect the lid switch wire connecter.
6
Using a flat-head screwdriver, release the spring clips securing the cabinet to the rear panel.
7
Tilt the cabinet toward you, slide forward and remove.
8
Use pliers to release the retaining clamps securing the valve outlet hose to the fill spout and the thermistor then pull the old hose free.
9
Remove the larger retaining clamp from the hose and leave the smaller clamp resting on the thermistor.
10
Install the new valve outlet hose by sliding the large retaining clamp over the larger end of the hose.
11
Attach that end to the fill spout and secure it with the clamp.
12
Attach the opposite end to the thermistor and use the clamp to secure.
13
Reinstall the cabinet by sliding the front edge of the cabinet underneath the base frame.
14
Use your foot to push it into position.
15
Align the two notches in each side of the cabinet with the tabs on each side of the base frame.
16
Make sure the sides of the cabinet are properly aligned with the rear panel.
17
Reinstall the spring clips to secure the cabinet.
18
Reconnect the lid switch wire connecter.
19
Lower the control panel and snap the retaining clips into the slots in the main top.
20
Rethread and tighten the screws to secure the control panel.
21
Realign the end caps and snap them into place.
22
With the repair completed plug the power cord back in and your washer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com