Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Refrigerator Icemaker Evaporator Heater #242094802
Frigidaire Refrigerator Icemaker Evaporator Heater #242094802
Skill Level
Total Parts Cost
$91.94Estimated Savings
$112.5007:17
- Description
This video provides step-by-step repair instructions for replacing the icemaker evaporator heater on a Frigidaire refrigerator. The most common reason for replacing the heater is if the icemaker evaporator freezes over and stops making ice cubes.
All of the information for this refrigerator heater replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: phillips head screwdriver, 1/4" socket
All of the information for this refrigerator heater replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: phillips head screwdriver, 1/4" socket
Step By Step Instructions
1
Before you replace the icemaker evaporator heater in your refrigerator be sure to unplug the power cord.
2
Your first step is to fully remove the ice bucket.
3
Use a phillips-head screwdriver or a number two square drive bit to unthread the screws to release the icemaker’s front cover.
4
Using a quarter-inch socket or nut driver, unthread the screw securing the wire harness cover.
5
Remove the cover.
6
Disconnect the wire connecters.
7
Pull the icemaker forward to detach.
8
Next, remove the shelving adjacent to the icemaker.
9
Now unthread the three mounting screws securing the icemaker housing.
10
Remove the housing and set it aside.
11
Move the icemaker out of the way.
12
Unthread the screws securing the auger motor housing to the rear panel.
13
Depress the tabs to release the wire connecter and fully remove the auger motor assembly and icemaker.
14
Remove any shelving below the evaporator.
15
Depress the tabs to release the wire connecter from the bracket.
16
Unhook the defrost thermostat wires from the evaporator cover and pull the cover down to remove.
17
Use a precision flat-head screwdriver to help release the tabs securing the two thermostat wire terminals to the connecter.
18
Now cut the zip-ties securing the heater to the evaporator coil.
19
Pull the old heater assembly free.
20
Install the new evaporator heater by aligning it in the grooves on the evaporator and pushing it into place.
21
Use zip-ties to secure.
22
Make sure the thermostat wire terminal tabs are bent outwards.
23
Now insert the wire terminals into the connecter until they snap into place.
24
Slide the evaporator cover back on and secure the wires behind the retaining clip.
25
Snap the wire connecter back into the bracket.
26
Replace the shelving if necessary.
27
Return the auger motor assembly and icemaker to the refrigerator and reconnect the wire connecter.
28
Reposition the auger motor housing and secure it to the rear panel with the screws.
29
Reinstall the icemaker housing by first inserting the icemaker through the rear then feed the wires through the hole at the top.
30
Fully position the housing and secure it with the mounting screws.
31
Replace the shelving.
32
Realign the icemaker on the housing mounting studs and push back until the icemaker locks into place.
33
Connect the wire connecters.
34
Realign the wire harness cover and secure it with the screw.
35
Reposition the front cover then rethread and tighten the screws to secure.
36
Replace the ice bucket.
37
With the repair completed plug the power cord back in and your refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the icemaker evaporator heater on a Frigidaire refrigerator. The most common reason for replacing the heater is if the icemaker evaporator freezes over and stops making ice cubes.
All of the information for this refrigerator heater replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: phillips head screwdriver, 1/4" socket
All of the information for this refrigerator heater replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: phillips head screwdriver, 1/4" socket
Step-By-Step Instructions
1
Before you replace the icemaker evaporator heater in your refrigerator be sure to unplug the power cord.
2
Your first step is to fully remove the ice bucket.
3
Use a phillips-head screwdriver or a number two square drive bit to unthread the screws to release the icemaker’s front cover.
4
Using a quarter-inch socket or nut driver, unthread the screw securing the wire harness cover.
5
Remove the cover.
6
Disconnect the wire connecters.
7
Pull the icemaker forward to detach.
8
Next, remove the shelving adjacent to the icemaker.
9
Now unthread the three mounting screws securing the icemaker housing.
10
Remove the housing and set it aside.
11
Move the icemaker out of the way.
12
Unthread the screws securing the auger motor housing to the rear panel.
13
Depress the tabs to release the wire connecter and fully remove the auger motor assembly and icemaker.
14
Remove any shelving below the evaporator.
15
Depress the tabs to release the wire connecter from the bracket.
16
Unhook the defrost thermostat wires from the evaporator cover and pull the cover down to remove.
17
Use a precision flat-head screwdriver to help release the tabs securing the two thermostat wire terminals to the connecter.
18
Now cut the zip-ties securing the heater to the evaporator coil.
19
Pull the old heater assembly free.
20
Install the new evaporator heater by aligning it in the grooves on the evaporator and pushing it into place.
21
Use zip-ties to secure.
22
Make sure the thermostat wire terminal tabs are bent outwards.
23
Now insert the wire terminals into the connecter until they snap into place.
24
Slide the evaporator cover back on and secure the wires behind the retaining clip.
25
Snap the wire connecter back into the bracket.
26
Replace the shelving if necessary.
27
Return the auger motor assembly and icemaker to the refrigerator and reconnect the wire connecter.
28
Reposition the auger motor housing and secure it to the rear panel with the screws.
29
Reinstall the icemaker housing by first inserting the icemaker through the rear then feed the wires through the hole at the top.
30
Fully position the housing and secure it with the mounting screws.
31
Replace the shelving.
32
Realign the icemaker on the housing mounting studs and push back until the icemaker locks into place.
33
Connect the wire connecters.
34
Realign the wire harness cover and secure it with the screw.
35
Reposition the front cover then rethread and tighten the screws to secure.
36
Replace the ice bucket.
37
With the repair completed plug the power cord back in and your refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Defrost Heater Assembly
$91.94
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com