Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Refrigerator Power Cord Replacement #241516901
Frigidaire Refrigerator Power Cord Replacement #241516901
Skill Level
Total Parts Cost
$47.32Estimated Savings
$112.5003:53
- Description
This video provides step-by-step repair instructions for replacing the power cord on a Frigidaire refrigerator. The most common reason for replacing the cord is if the refrigerator will not power on at all.
All of the information for this refrigerator power cord replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: 1/4" socket, phillips head screwdriver, flat head screwdriver
All of the information for this refrigerator power cord replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: 1/4" socket, phillips head screwdriver, flat head screwdriver
Step By Step Instructions
1
Make sure the old power cord is unplugged
2
Shut off the water supply.
3
Use a quarter-inch socket or nut driver to unthread the screw securing the water supply line retainer to the rear panel.
4
Detach the water supply line from the inlet valve.
5
Next, unthread the remaining screws securing the rear access panel.
6
Set the panel aside.
7
To make it easier to access the power cord grounding wire mounting screw, you can move the compressor and inverter board out of the way.
8
Pull off the three retaining pins and remove the washers.
9
Now carefully lift up the compressor and inverter board and move them to the right.
10
Unthread the screw securing the power cord retaining clip as well as the screw securing the grounding wire.
11
You can now disconnect the wire connecter to fully remove the old power cord.
12
Prepare the new power cord for installation by transferring the retaining clip from the old cord to the new one.
13
Now connect the wire connecter
14
Secure the grounding wire to the refrigerator base with the screw.
15
Thread and tighten the screw to secure the power cord retaining clip.
16
Now reposition the compressor and inverter board.
17
With the washers in place, secure the compressor with the three retaining pins.
18
Reposition the rear access panel
19
Secure it with the screws.
20
Reattach the water supply line to the inlet valve.
21
Secure the line to the rear panel with the retainer.
22
With the repair completed turn the water supply back on
23
Plug the new power cord in and your refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the power cord on a Frigidaire refrigerator. The most common reason for replacing the cord is if the refrigerator will not power on at all.
All of the information for this refrigerator power cord replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: 1/4" socket, phillips head screwdriver, flat head screwdriver
All of the information for this refrigerator power cord replacement video is applicable to the following brands:
Arctic Air, Crosley, Electrolux, Frigidaire, Gibson, Kelvinator, Tappan, Westinghouse
Tools needed: 1/4" socket, phillips head screwdriver, flat head screwdriver
Step-By-Step Instructions
1
Make sure the old power cord is unplugged
2
Shut off the water supply.
3
Use a quarter-inch socket or nut driver to unthread the screw securing the water supply line retainer to the rear panel.
4
Detach the water supply line from the inlet valve.
5
Next, unthread the remaining screws securing the rear access panel.
6
Set the panel aside.
7
To make it easier to access the power cord grounding wire mounting screw, you can move the compressor and inverter board out of the way.
8
Pull off the three retaining pins and remove the washers.
9
Now carefully lift up the compressor and inverter board and move them to the right.
10
Unthread the screw securing the power cord retaining clip as well as the screw securing the grounding wire.
11
You can now disconnect the wire connecter to fully remove the old power cord.
12
Prepare the new power cord for installation by transferring the retaining clip from the old cord to the new one.
13
Now connect the wire connecter
14
Secure the grounding wire to the refrigerator base with the screw.
15
Thread and tighten the screw to secure the power cord retaining clip.
16
Now reposition the compressor and inverter board.
17
With the washers in place, secure the compressor with the three retaining pins.
18
Reposition the rear access panel
19
Secure it with the screws.
20
Reattach the water supply line to the inlet valve.
21
Secure the line to the rear panel with the retainer.
22
With the repair completed turn the water supply back on
23
Plug the new power cord in and your refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Power Cord
$47.32
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com