Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Alpha Electric Dryer Motor Pulley Replacement #WP8066184
Whirlpool Alpha Electric Dryer Motor Pulley Replacement #WP8066184
Skill Level
Total Parts Cost
$40.94Estimated Savings
$112.5009:26
- Description
This video provides step-by-step repair instructions for replacing the motor pulley on a Whirlpool electric dryer (model #WED85HEFW0). The most common reason for replacing the pulley is if the motor is running but the drum is not spinning.
This pulley replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, Phillips-head screwdriver, 1/4" socket
Don't forget to like and comment on this video and subscribe to our channel!
This pulley replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, Phillips-head screwdriver, 1/4" socket
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace the motor pulley in your dryer be sure to unplug the power cord.
2
Use a quarter-inch socket or nut driver to unthread the rear screws securing the top panel and bracket to the rear panel.
3
Slide the top panel back and lift up to detach.
4
Next, unthread the screws securing the control housing.
5
Disconnect the control panel wire connecter from the control board.
6
You can now lift the control housing and panel up and out to remove.
7
Disconnect the door switch wire harness.
8
Lift up the front of the dryer and support it.
9
Use the quarter-inch socket or nut driver to fully unthread the outer screws securing the bottom of the front panel.
10
Loosen the two middle screws.
11
Remove the support and lower the appliance.
12
Now open the dryer door and use a Phillips-head screwdriver to unthread the two screws securing the front panel to the bulkhead.
13
Use the quarter-inch socket or nut driver to unthread the three top screws.
14
Now lift the front panel up and out to remove.
15
Next, unthread the screws securing the control housing bracket.
16
Unthread the screw securing the front of the control board bracket.
17
Use wire or tape to support the bracket.
18
You can now lift the control housing bracket up to remove.
19
Disconnect the moisture sensor wire harness.
20
Unthread the screw to release the lower retaining bracket.
21
Now unthread the four screws securing the front bulkhead to the frame.
22
Lift the bulkhead up and detach it from the drum and frame.
23
Now reach under the drum and push the idler pulley to release the tension on the belt then unthread the belt from the idler pulley and motor pulley.
24
You can use the belt to help lift out the drum.
25
Use a 7/16th inch wrench to secure the motor shaft and pliers to loosen the motor pulley by rotating it counter-clockwise.
26
Unthread the old pulley.
27
Install the new motor pulley by threading it clockwise onto the motor shaft.
28
Use the 7/16th inch wrench and pliers to tighten.
29
Replace the drum by aligning the smaller rim on the rear rollers.
30
Loop the belt around the motor pulley and the idler pulley in a zig-zag formation.
31
Now, rotate the drum to help align the belt.
32
Reinstall the front bulkhead by hooking it onto the frame as you align the rollers under the drum.
33
Rethread and tighten the four screws to secure the bulkhead.
34
Reposition the lower retaining bracket and secure it with the screw.
35
Reconnect the moisture sensor wire harness.
36
Reposition the control housing bracket on the frame under the control board bracket.
37
Replace the screws to secure.
38
Reposition the front panel on the loosened screws
39
Feed the wire under the control housing bracket
40
Then align the top edge of the panel on the mounting tabs.
41
Thread and tighten the top screws.
42
Replace the screws behind the door.
43
Support the dryer
44
Tighten the two middle screws securing the bottom of the front panel.
45
Thread and tighten the outer screws.
46
Remove the support.
47
Connect the door switch wire harness.
48
Feed the control panel wire through the housing and control board mounting brackets and snap the control housing into place.
49
Thread the screws to secure.
50
Connect the wire connecter to the control board.
51
Realign the top panel and bracket then slide into position.
52
Rethread the rear screws and tighten.
53
With the repair completed plug the power cord back in and your dryer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the motor pulley on a Whirlpool electric dryer (model #WED85HEFW0). The most common reason for replacing the pulley is if the motor is running but the drum is not spinning.
This pulley replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, Phillips-head screwdriver, 1/4" socket
Don't forget to like and comment on this video and subscribe to our channel!
This pulley replacement video is applicable to the following brands:
Whirlpool, Maytag
Tools needed: T-25 Torx bit, Phillips-head screwdriver, 1/4" socket
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace the motor pulley in your dryer be sure to unplug the power cord.
2
Use a quarter-inch socket or nut driver to unthread the rear screws securing the top panel and bracket to the rear panel.
3
Slide the top panel back and lift up to detach.
4
Next, unthread the screws securing the control housing.
5
Disconnect the control panel wire connecter from the control board.
6
You can now lift the control housing and panel up and out to remove.
7
Disconnect the door switch wire harness.
8
Lift up the front of the dryer and support it.
9
Use the quarter-inch socket or nut driver to fully unthread the outer screws securing the bottom of the front panel.
10
Loosen the two middle screws.
11
Remove the support and lower the appliance.
12
Now open the dryer door and use a Phillips-head screwdriver to unthread the two screws securing the front panel to the bulkhead.
13
Use the quarter-inch socket or nut driver to unthread the three top screws.
14
Now lift the front panel up and out to remove.
15
Next, unthread the screws securing the control housing bracket.
16
Unthread the screw securing the front of the control board bracket.
17
Use wire or tape to support the bracket.
18
You can now lift the control housing bracket up to remove.
19
Disconnect the moisture sensor wire harness.
20
Unthread the screw to release the lower retaining bracket.
21
Now unthread the four screws securing the front bulkhead to the frame.
22
Lift the bulkhead up and detach it from the drum and frame.
23
Now reach under the drum and push the idler pulley to release the tension on the belt then unthread the belt from the idler pulley and motor pulley.
24
You can use the belt to help lift out the drum.
25
Use a 7/16th inch wrench to secure the motor shaft and pliers to loosen the motor pulley by rotating it counter-clockwise.
26
Unthread the old pulley.
27
Install the new motor pulley by threading it clockwise onto the motor shaft.
28
Use the 7/16th inch wrench and pliers to tighten.
29
Replace the drum by aligning the smaller rim on the rear rollers.
30
Loop the belt around the motor pulley and the idler pulley in a zig-zag formation.
31
Now, rotate the drum to help align the belt.
32
Reinstall the front bulkhead by hooking it onto the frame as you align the rollers under the drum.
33
Rethread and tighten the four screws to secure the bulkhead.
34
Reposition the lower retaining bracket and secure it with the screw.
35
Reconnect the moisture sensor wire harness.
36
Reposition the control housing bracket on the frame under the control board bracket.
37
Replace the screws to secure.
38
Reposition the front panel on the loosened screws
39
Feed the wire under the control housing bracket
40
Then align the top edge of the panel on the mounting tabs.
41
Thread and tighten the top screws.
42
Replace the screws behind the door.
43
Support the dryer
44
Tighten the two middle screws securing the bottom of the front panel.
45
Thread and tighten the outer screws.
46
Remove the support.
47
Connect the door switch wire harness.
48
Feed the control panel wire through the housing and control board mounting brackets and snap the control housing into place.
49
Thread the screws to secure.
50
Connect the wire connecter to the control board.
51
Realign the top panel and bracket then slide into position.
52
Rethread the rear screws and tighten.
53
With the repair completed plug the power cord back in and your dryer should be ready for use.
Applicable Product Model
Parts Needed
Motor Pulley
$40.94
Total$0.00
Related Articles & Videos
10:42
Part Replacement
Whirlpool Alpha Electric Dryer Heating Element Replacement #WP8544771
00:47
Part Replacement
Whirlpool Alpha Electric Dryer Drying Rack Installation #W10886894
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com