Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairNoisy Duet/HE3 Dryer? Drum Roller Replacement #W10314173
Noisy Duet/HE3 Dryer? Drum Roller Replacement #W10314173
Skill Level
Total Parts Cost
$22.20Estimated Savings
$112.5004:41
- Description
This video provides step-by-step instructions for replacing a dryer drum support roller on Duet/HE3 dryers. The most common reason for replacing a drum roller are if the dryer is making squeaking noises, stops turning during a cycle, or won’t turn at all.
All the information in this drum roller replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Maytag, Amana, Crosley, Inglis, Admiral
Tools used: hex socket, flat head screwdriver, Phillips head screwdriver
All the information in this drum roller replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Maytag, Amana, Crosley, Inglis, Admiral
Tools used: hex socket, flat head screwdriver, Phillips head screwdriver
Step By Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the top panel screws and set the panel aside.
3
Next, depress the tabs on the control panel and pull it off.
4
Disconnect the wire harness.
5
Remove the screws to release the circuit board bracket.
6
Remove the control bracket screws and detach the bracket.
7
Now, remove the screws located at the base of the dryer.
8
Pull the lower panel out and then down to detach.
9
Reach into the lower cabinet to disconnect the door switch and moisture sensor wire harnesses.
10
Remove the screws at the bottom and at the top of the front panel.
11
Remove the mounting screws located inside the door to release the front panel.
12
Remove the lower bulkhead mounting screws and loosen the upper screws.
13
Remove the mounting screws from the blower housing.
14
Lift the bulkhead off the upper mounting screws and set it aside.
15
Next, remove the dryer belt by depressing the pulley to release the tension and unthreading the belt from the pulley and motor shaft.
16
Now use the belt to lift out the drum.
17
If still intact, remove the old roller by releasing the front tri-ring and sliding the roller off of the shaft.
18
Remove the back tri-ring as well.
19
You’re now ready to install the new support roller.
20
Clean the shaft and install the back tri-ring.
21
Slide on the new roller and secure with the front tri-ring.
22
Now, replace the drum by aligning its rim on the two rear rollers and loop the belt around the tension pulley and motor shaft in a “zig-zag” formation.
23
Rotate the drum to help align the belt.
24
Now, reinstall the bulkhead by aligning it on the upper screws.
25
Tighten these screws then replace the lower screws as well as the blower housing screws.
26
Reattach the front panel by lining it up on the cabinet then, secure it with the upper and lower screws as well as the screws inside the door.
27
Reconnect the door switch and moisture sensor wire harnesses.
28
Slide the lower panel up into position and secure it with the screws.
29
Reinstall the control panel bracket.
30
Reattach the circuit board bracket.
31
Reconnect the control panel’s wire harness and snap the panel back into place.
32
Replace the top panel secure it with the screws. and plug the appliance back in to make sure it’s functioning properly.
Description
This video provides step-by-step instructions for replacing a dryer drum support roller on Duet/HE3 dryers. The most common reason for replacing a drum roller are if the dryer is making squeaking noises, stops turning during a cycle, or won’t turn at all.
All the information in this drum roller replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Maytag, Amana, Crosley, Inglis, Admiral
Tools used: hex socket, flat head screwdriver, Phillips head screwdriver
All the information in this drum roller replacement video is applicable to the following brands: Kenmore, Whirlpool, KitchenAid, Maytag, Amana, Crosley, Inglis, Admiral
Tools used: hex socket, flat head screwdriver, Phillips head screwdriver
Step-By-Step Instructions
1
As with any repair, be sure you unplug the appliance before beginning.
2
Your first step is to remove the top panel screws and set the panel aside.
3
Next, depress the tabs on the control panel and pull it off.
4
Disconnect the wire harness.
5
Remove the screws to release the circuit board bracket.
6
Remove the control bracket screws and detach the bracket.
7
Now, remove the screws located at the base of the dryer.
8
Pull the lower panel out and then down to detach.
9
Reach into the lower cabinet to disconnect the door switch and moisture sensor wire harnesses.
10
Remove the screws at the bottom and at the top of the front panel.
11
Remove the mounting screws located inside the door to release the front panel.
12
Remove the lower bulkhead mounting screws and loosen the upper screws.
13
Remove the mounting screws from the blower housing.
14
Lift the bulkhead off the upper mounting screws and set it aside.
15
Next, remove the dryer belt by depressing the pulley to release the tension and unthreading the belt from the pulley and motor shaft.
16
Now use the belt to lift out the drum.
17
If still intact, remove the old roller by releasing the front tri-ring and sliding the roller off of the shaft.
18
Remove the back tri-ring as well.
19
You’re now ready to install the new support roller.
20
Clean the shaft and install the back tri-ring.
21
Slide on the new roller and secure with the front tri-ring.
22
Now, replace the drum by aligning its rim on the two rear rollers and loop the belt around the tension pulley and motor shaft in a “zig-zag” formation.
23
Rotate the drum to help align the belt.
24
Now, reinstall the bulkhead by aligning it on the upper screws.
25
Tighten these screws then replace the lower screws as well as the blower housing screws.
26
Reattach the front panel by lining it up on the cabinet then, secure it with the upper and lower screws as well as the screws inside the door.
27
Reconnect the door switch and moisture sensor wire harnesses.
28
Slide the lower panel up into position and secure it with the screws.
29
Reinstall the control panel bracket.
30
Reattach the circuit board bracket.
31
Reconnect the control panel’s wire harness and snap the panel back into place.
32
Replace the top panel secure it with the screws. and plug the appliance back in to make sure it’s functioning properly.
Applicable Product Model
Related Articles & Videos
07:02
Part Replacement
Whirlpool Electric Washer/Dryer Combo Drum Roller Replacement #WPW10314173
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com