Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Double Wall Oven Meat Probe Jack Replacement #W10696226
Kitchenaid Double Wall Oven Meat Probe Jack Replacement #W10696226
Skill Level
Total Parts Cost
$49.89Estimated Savings
$112.5008:30
- Description
This video provides step-by-step repair instructions for replacing the meat probe jack on a Kitchenaid Double Wall Oven (model #KODE500ESS02). The most common reason for replacing the jack is if the meat probe sensor will not work properly.
All of the information for this jack replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
All of the information for this jack replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
Step By Step Instructions
1
KitchenAid Built-In Double Oven - KODE500ESS02
2
Double Wall Oven Meat Probe Jack Replacement
3
Tools needed: 3/8th inch wrench, Phillips-head screwdriver, quarter-inch nut driver
4
Shock
5
Before you do this, be sure to shut off the power to the oven junction box.
6
Fully open the top oven door and rotate both door hinge locks back.
7
Partially close the door, then lift and pull the door toward you to remove.
8
With the handle side down, set the door on a blanket.
9
Repeat this procedure to remove the bottom oven door.
10
Using a Phillips-head screwdriver, unthread the two screws to release the bottom vent.
11
Remove all of the oven racks.
12
Now use a Phillips-head screwdriver to unthread the four screws securing the wall oven frame to the cabinet.
13
Heavy
14
Have an assistant help you to carefully lift the appliance out of the cabinet and set it on a piece of cardboard to protect the floor.
15
Be aware that if the conduit cable is not long enough to move the wall oven, you will need to disconnect the power and grounding wires from the junction box.
16
When replacing the meat probe jack in the upper oven, use a quarter-inch nut driver to unthread the screws securing the upper rear access panel.
17
If replacing the jack in the lower oven, both the upper and lower rear access panels will need to be removed.
18
Next, unthread the screws securing the top right side panel.
19
When replacing a jack in the lower oven, both the top and bottom side panels will need to be removed.
20
Sharp
21
Carefully remove the panel or panels.
22
Disconnect the meat probe jack wire connecter and feed it through the rear panel.
23
Now use a 3/8th inch wrench to unthread the nut securing the jack and remove the nut and lock washer.
24
You can now remove the old jack assembly.
25
Install the new meat probe jack by aligning it in the wall of the oven.
26
Position the lock washer, then thread and tighten the nut.
27
Feed the wire through the hole in the rear panel and connect the wire connecter.
28
Reposition the side panel or panels and replace all of the screws.
29
Realign the lower rear access panel if necessary and thread and tighten the screws to secure.
30
Do the same to reinstall the upper rear access panel.
31
Return the wall oven to the cabinet and push it into position.
32
Confirm that the side trim pieces are in place, then thread the screws to secure the frame to the cabinet.
33
Realign the bottom vent on the oven frame, then thread and tighten the two screws to secure.
34
Replace the oven racks.
35
Reinstall the oven doors by inserting the door hinges into the hinge slots at a forty-five degree angle.
36
Lower the doors to their fully open position, then rotate the hinge locks forward.
37
With the repair completed, turn the power supply back on and the double wall oven should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the meat probe jack on a Kitchenaid Double Wall Oven (model #KODE500ESS02). The most common reason for replacing the jack is if the meat probe sensor will not work properly.
All of the information for this jack replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
All of the information for this jack replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
Step-By-Step Instructions
1
KitchenAid Built-In Double Oven - KODE500ESS02
2
Double Wall Oven Meat Probe Jack Replacement
3
Tools needed: 3/8th inch wrench, Phillips-head screwdriver, quarter-inch nut driver
4
Shock
5
Before you do this, be sure to shut off the power to the oven junction box.
6
Fully open the top oven door and rotate both door hinge locks back.
7
Partially close the door, then lift and pull the door toward you to remove.
8
With the handle side down, set the door on a blanket.
9
Repeat this procedure to remove the bottom oven door.
10
Using a Phillips-head screwdriver, unthread the two screws to release the bottom vent.
11
Remove all of the oven racks.
12
Now use a Phillips-head screwdriver to unthread the four screws securing the wall oven frame to the cabinet.
13
Heavy
14
Have an assistant help you to carefully lift the appliance out of the cabinet and set it on a piece of cardboard to protect the floor.
15
Be aware that if the conduit cable is not long enough to move the wall oven, you will need to disconnect the power and grounding wires from the junction box.
16
When replacing the meat probe jack in the upper oven, use a quarter-inch nut driver to unthread the screws securing the upper rear access panel.
17
If replacing the jack in the lower oven, both the upper and lower rear access panels will need to be removed.
18
Next, unthread the screws securing the top right side panel.
19
When replacing a jack in the lower oven, both the top and bottom side panels will need to be removed.
20
Sharp
21
Carefully remove the panel or panels.
22
Disconnect the meat probe jack wire connecter and feed it through the rear panel.
23
Now use a 3/8th inch wrench to unthread the nut securing the jack and remove the nut and lock washer.
24
You can now remove the old jack assembly.
25
Install the new meat probe jack by aligning it in the wall of the oven.
26
Position the lock washer, then thread and tighten the nut.
27
Feed the wire through the hole in the rear panel and connect the wire connecter.
28
Reposition the side panel or panels and replace all of the screws.
29
Realign the lower rear access panel if necessary and thread and tighten the screws to secure.
30
Do the same to reinstall the upper rear access panel.
31
Return the wall oven to the cabinet and push it into position.
32
Confirm that the side trim pieces are in place, then thread the screws to secure the frame to the cabinet.
33
Realign the bottom vent on the oven frame, then thread and tighten the two screws to secure.
34
Replace the oven racks.
35
Reinstall the oven doors by inserting the door hinges into the hinge slots at a forty-five degree angle.
36
Lower the doors to their fully open position, then rotate the hinge locks forward.
37
With the repair completed, turn the power supply back on and the double wall oven should be ready for use.
Applicable Product Model
Related Articles & Videos
03:31
Part Replacement
Kitchenaid Double Wall Oven Control Panel Assembly (Black) Replacement #W11087449
02:50
Part Replacement
Kitchenaid Double Wall Oven Inner Door Glass Replacement #W10827059
08:02
Part Replacement
Kitchenaid Double Wall Oven Cooling Fan Blower Replacement #W10861504
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com