Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Double Wall Oven Lower Oven Control Board Replacement #W10801665
Kitchenaid Double Wall Oven Lower Oven Control Board Replacement #W10801665
Skill Level
Total Parts Cost
$384.26Estimated Savings
$112.5006:20
- Description
This video provides step-by-step repair instructions for replacing the lower oven control board on a Kitchenaid Double Wall Oven (model #KODE500ESS02). The most common reason for replacing the control board is if the oven will not work at all.
All of the information for this control board replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
All of the information for this control board replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
Step By Step Instructions
1
KitchenAid Built-In Double Oven - KODE500ESS02
2
Double Wall Oven Lower Oven Control Board Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock
5
Before you do this, be sure to shut off the power to the oven junction box.
6
Fully open the top oven door and rotate both door hinge locks back.
7
Partially close the door, then lift and pull the door toward you to remove.
8
With the handle side down, set the door on a blanket.
9
Repeat this procedure to remove the bottom oven door.
10
Using a Phillips-head screwdriver, unthread the two screws to release the bottom vent.
11
Remove all of the oven racks.
12
Now use a Phillips-head screwdriver to unthread the four screws securing the wall oven frame to the cabinet.
13
Heavy
14
Have an assistant help you to carefully lift the appliance out of the cabinet and set it on a piece of cardboard to protect the floor.
15
Be aware that if the conduit cable is not long enough to move the wall oven, you will need to disconnect the power and grounding wires from the junction box.
16
Now use the Phillips-head screwdriver or a quarter-inch nut driver to unthread the eight screws securing the control board cover.
17
Sharp
18
With the screws removed, lift off the cover.
19
Note the orientation of the wires connected to the control board?then disconnect them.
20
Next, unthread the two mounting screws.
21
Slide the board to the left to remove.
22
Install the new control board by inserting the tabs into the slots in the mounting plate.
23
Thread the screws to secure.
24
Connect all of the wires to the appropriate terminals on the board.
25
Reposition the control board cover, then thread and tighten the screws to secure ? be sure to secure the bumpers under the appropriate screws.
26
Return the wall oven to the cabinet and push it into position.
27
Confirm that the side trim pieces are in place, then thread the screws to secure the frame to the cabinet.
28
Realign the bottom vent on the oven frame, then thread and tighten the two screws to secure.
29
Replace the oven racks.
30
Reinstall the oven doors by inserting the door hinges into the hinge slots at a forty-five degree angle.
31
Lower the doors to their fully open position, then rotate the hinge locks forward.
32
With the repair completed, turn the power supply back on and the double wall oven should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the lower oven control board on a Kitchenaid Double Wall Oven (model #KODE500ESS02). The most common reason for replacing the control board is if the oven will not work at all.
All of the information for this control board replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
All of the information for this control board replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
Step-By-Step Instructions
1
KitchenAid Built-In Double Oven - KODE500ESS02
2
Double Wall Oven Lower Oven Control Board Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock
5
Before you do this, be sure to shut off the power to the oven junction box.
6
Fully open the top oven door and rotate both door hinge locks back.
7
Partially close the door, then lift and pull the door toward you to remove.
8
With the handle side down, set the door on a blanket.
9
Repeat this procedure to remove the bottom oven door.
10
Using a Phillips-head screwdriver, unthread the two screws to release the bottom vent.
11
Remove all of the oven racks.
12
Now use a Phillips-head screwdriver to unthread the four screws securing the wall oven frame to the cabinet.
13
Heavy
14
Have an assistant help you to carefully lift the appliance out of the cabinet and set it on a piece of cardboard to protect the floor.
15
Be aware that if the conduit cable is not long enough to move the wall oven, you will need to disconnect the power and grounding wires from the junction box.
16
Now use the Phillips-head screwdriver or a quarter-inch nut driver to unthread the eight screws securing the control board cover.
17
Sharp
18
With the screws removed, lift off the cover.
19
Note the orientation of the wires connected to the control board?then disconnect them.
20
Next, unthread the two mounting screws.
21
Slide the board to the left to remove.
22
Install the new control board by inserting the tabs into the slots in the mounting plate.
23
Thread the screws to secure.
24
Connect all of the wires to the appropriate terminals on the board.
25
Reposition the control board cover, then thread and tighten the screws to secure ? be sure to secure the bumpers under the appropriate screws.
26
Return the wall oven to the cabinet and push it into position.
27
Confirm that the side trim pieces are in place, then thread the screws to secure the frame to the cabinet.
28
Realign the bottom vent on the oven frame, then thread and tighten the two screws to secure.
29
Replace the oven racks.
30
Reinstall the oven doors by inserting the door hinges into the hinge slots at a forty-five degree angle.
31
Lower the doors to their fully open position, then rotate the hinge locks forward.
32
With the repair completed, turn the power supply back on and the double wall oven should be ready for use.
Applicable Product Model
Related Articles & Videos
03:31
Part Replacement
Kitchenaid Double Wall Oven Control Panel Assembly (Black) Replacement #W11087449
02:50
Part Replacement
Kitchenaid Double Wall Oven Inner Door Glass Replacement #W10827059
08:02
Part Replacement
Kitchenaid Double Wall Oven Cooling Fan Blower Replacement #W10861504
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com