Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Double Wall Oven Broil Element Replacement #W10804429
Kitchenaid Double Wall Oven Broil Element Replacement #W10804429
Skill Level
Total Parts Cost
$90.94Estimated Savings
$112.5003:57
- Description
This video provides step-by-step repair instructions for replacing the broil element on a Kitchenaid Double Wall Oven (model #KODE500ESS02). The most common reason for replacing the broil element is if it is burned out and will not heat the oven.
All of the information for this element replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
All of the information for this element replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
Step By Step Instructions
1
KitchenAid Built-In Double Oven - KODE500ESS02
2
Double Wall Oven Broil Element Replacement
3
Tools needed: quarter-inch nut driver or a Phillips-head screwdriver
4
Shock
5
Be sure to shut off the power to the oven junction box.
6
For easier access to the rear of the oven, we recommend removing the appropriate oven door.
7
Fully open the door and rotate both door hinge locks back.
8
Heavy
9
Partially close the door, then lift and pull the door toward you to remove.
10
With the handle side down, set the door on a blanket.
11
Remove any racks that are in the way.
12
Using a quarter-inch nut driver or a Phillips-head screwdriver, unthread the two screws securing the rear broil element mounting plate.
13
Next, unthread the two screws securing the upper shields.
14
Sharp
15
Pull the shield and element away from the rear of the oven and disconnect the wires from the element terminals ? make sure the wires don?t slip through the holes behind the rear panel.
16
Prepare the new broil element for installation by transferring the shield from the old element to the new one.
17
Unthread the screws to release the element brackets from the shield.
18
Align the new element brackets on the shield and secure them with the screws.
19
Now connect the wires to the element terminals.
20
Realign the shield by first inserting the oven sensor through the large hole.
21
Realign the smaller front shield, then thread and tighten the two front screws to secure the assembly.
22
Replace the screws to secure the rear mounting plate as well.
23
Replace any oven racks.
24
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
25
Lower the door to its fully open position, then rotate the hinge locks forward.
26
With the repair completed, turn the power supply back on and the double wall oven should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the broil element on a Kitchenaid Double Wall Oven (model #KODE500ESS02). The most common reason for replacing the broil element is if it is burned out and will not heat the oven.
All of the information for this element replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
All of the information for this element replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
Step-By-Step Instructions
1
KitchenAid Built-In Double Oven - KODE500ESS02
2
Double Wall Oven Broil Element Replacement
3
Tools needed: quarter-inch nut driver or a Phillips-head screwdriver
4
Shock
5
Be sure to shut off the power to the oven junction box.
6
For easier access to the rear of the oven, we recommend removing the appropriate oven door.
7
Fully open the door and rotate both door hinge locks back.
8
Heavy
9
Partially close the door, then lift and pull the door toward you to remove.
10
With the handle side down, set the door on a blanket.
11
Remove any racks that are in the way.
12
Using a quarter-inch nut driver or a Phillips-head screwdriver, unthread the two screws securing the rear broil element mounting plate.
13
Next, unthread the two screws securing the upper shields.
14
Sharp
15
Pull the shield and element away from the rear of the oven and disconnect the wires from the element terminals ? make sure the wires don?t slip through the holes behind the rear panel.
16
Prepare the new broil element for installation by transferring the shield from the old element to the new one.
17
Unthread the screws to release the element brackets from the shield.
18
Align the new element brackets on the shield and secure them with the screws.
19
Now connect the wires to the element terminals.
20
Realign the shield by first inserting the oven sensor through the large hole.
21
Realign the smaller front shield, then thread and tighten the two front screws to secure the assembly.
22
Replace the screws to secure the rear mounting plate as well.
23
Replace any oven racks.
24
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
25
Lower the door to its fully open position, then rotate the hinge locks forward.
26
With the repair completed, turn the power supply back on and the double wall oven should be ready for use.
Applicable Product Model
Related Articles & Videos
03:31
Part Replacement
Kitchenaid Double Wall Oven Control Panel Assembly (Black) Replacement #W11087449
02:50
Part Replacement
Kitchenaid Double Wall Oven Inner Door Glass Replacement #W10827059
08:02
Part Replacement
Kitchenaid Double Wall Oven Cooling Fan Blower Replacement #W10861504
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com