Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Double Wall Oven Convection Fan Blade Replacement #W10819914 
Kitchenaid Double Wall Oven Convection Fan Blade Replacement #W10819914
Skill Level
Total Parts Cost
$63.56Estimated Savings
$112.5002:55
- Description
This video provides step-by-step repair instructions for replacing the convection fan blade on a Kitchenaid Double Wall Oven (model #KODE500ESS02). The most common reason for replacing the blade is if it is damaged or jammed.
All of the information for this fan blade replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
All of the information for this fan blade replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
Step By Step Instructions
1
KitchenAid Built-In Double Oven - KODE500ESS02
2
Double Wall Oven Convection Fan Blade Replacement
3
Tools needed: Phillips-head screwdriver, half-inch socket
4
Shock
5
Be sure to shut off the power to the oven junction box.
6
For easier access to the rear of the oven, we recommend removing the appropriate oven door.
7
Fully open the door and rotate both door hinge locks back.
8
Heavy
9
Partially close the door, then lift and pull the door toward you to remove.
10
With the handle side down, set the door on a blanket.
11
Remove any racks that are in the way.
12
Using a Phillips-head screwdriver, unthread the two screws securing the convection fan cover.
13
Sharp
14
Pull the cover up to detach.
15
Use a half-inch socket to rotate the fan blade locking nut clockwise to loosen, then unthread the nut and remove the old blade.
16
Install the new convection fan blade by aligning it on the motor shaft, then thread the locking nut on counter-clockwise and tighten.
17
Replace the cover by inserting the tabs into the rear panel slots, then lift the cover up and rethread the screws to secure.
18
Replace any oven racks.
19
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
20
Lower the door to its fully open position, then rotate the hinge locks forward.
21
With the repair completed, turn the power supply back on and the double wall oven should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the convection fan blade on a Kitchenaid Double Wall Oven (model #KODE500ESS02). The most common reason for replacing the blade is if it is damaged or jammed.
All of the information for this fan blade replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
All of the information for this fan blade replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: Phillips-head screwdriver, 1/4" socket or nut driver
Step-By-Step Instructions
1
KitchenAid Built-In Double Oven - KODE500ESS02
2
Double Wall Oven Convection Fan Blade Replacement
3
Tools needed: Phillips-head screwdriver, half-inch socket
4
Shock
5
Be sure to shut off the power to the oven junction box.
6
For easier access to the rear of the oven, we recommend removing the appropriate oven door.
7
Fully open the door and rotate both door hinge locks back.
8
Heavy
9
Partially close the door, then lift and pull the door toward you to remove.
10
With the handle side down, set the door on a blanket.
11
Remove any racks that are in the way.
12
Using a Phillips-head screwdriver, unthread the two screws securing the convection fan cover.
13
Sharp
14
Pull the cover up to detach.
15
Use a half-inch socket to rotate the fan blade locking nut clockwise to loosen, then unthread the nut and remove the old blade.
16
Install the new convection fan blade by aligning it on the motor shaft, then thread the locking nut on counter-clockwise and tighten.
17
Replace the cover by inserting the tabs into the rear panel slots, then lift the cover up and rethread the screws to secure.
18
Replace any oven racks.
19
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
20
Lower the door to its fully open position, then rotate the hinge locks forward.
21
With the repair completed, turn the power supply back on and the double wall oven should be ready for use.
Applicable Product Model
Related Articles & Videos
04:30
Part Replacement
Kitchenaid Double Oven Electric Range Convection Fan Blade Replacement #W10819914
04:25
Part Replacement
Kitchenaid Double Oven Gas Range Convection Fan Blade Replacement #W10819914
03:31
Part Replacement
Kitchenaid Double Wall Oven Control Panel Assembly (Black) Replacement #W11087449
02:50
Part Replacement
Kitchenaid Double Wall Oven Inner Door Glass Replacement #W10827059
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com