Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenaid Microwave Main Control Board Replacement #W10915648 
Kitchenaid Microwave Main Control Board Replacement #W10915648
Skill Level
Total Parts Cost
$298.28Estimated Savings
$112.5004:13
- Description
This video provides step-by-step repair instructions for replacing the main control board on a Kitchenaid microwave (Model #KMBP100ESS01). The most common reason for replacing the board is if the microwave will not work at all.
All of the information for this microwave light bulb replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: multi-screwdriver
All of the information for this microwave light bulb replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: multi-screwdriver
Step By Step Instructions
1
Microwave Oven -Model KMBP100ESS01
2
KitchenAid Built-In Microwave Oven Main Control Board Replacement
3
ATTENTION: TOOLS & ASSISTANCE NEEDED:
4
Step 1: You will need a Phillips-head screwdriver or a quarter-inch nut driver and an assistant to help move heavy microwave.
5
"Step 2: Before you begin, be sure to turn off the power supply to the oven junction box. "
6
Step 3: Open the oven door and remove any racks from the oven along with the turntable and support.
7
Step 4: Now use a Phillips-head screwdriver or quarter-inch nut driver to unthread the two screws securing the mounting flanges to the cabinet.
8
Step 5: Remove the washers as well if still intact.
9
Step 6: Now have an assistant to help you pull the appliance out of the cabinet and set it on a sturdy surface.
10
Step 7: Be aware that if the conduit cable is not long enough to move the microwave oven you will need to disconnect the power and grounding wires and remove the conduit cable from the junction box.
11
Step 8: Use a Phillips-head screwdriver or a quarter-inch nut driver to unthread the four screws securing the top access panel.
12
Step 9: Lift the panel up then slide forward to remove.
13
"Step 10: Note the orientation of the wires connected to the main control board, then disconnect them. "
14
Step 11: Pull the front and side retaining tabs back to release the old board.
15
Step 12: Install the new control board by first positioning the rear edge under the tabs then secure the board under the front and side tabs.
16
Step 13: Connect the wires to the appropriate terminals on the new board.
17
Step 14: Replace the top access panel by inserting the rear edge first.
18
Step 15: Connect the wires to the appropriate terminals on the new board.
19
Step 16: Replace the top access panel by inserting the rear edge first.
20
Step 17: Secure it with the screws.
21
"Step 18: With an assistant, return the microwave oven to the cabinet and push it into position. "
22
Step 19: Insert the washers into the holes in the flanges then thread the two screws to secure the flanges to the cabinet.
23
Step 20: Replace the support and align the turntable on the coupling.
24
Step 21: Turn on the power supply back on to the microwave.
25
Congrats! Your microwave oven is ready for use.
Description
This video provides step-by-step repair instructions for replacing the main control board on a Kitchenaid microwave (Model #KMBP100ESS01). The most common reason for replacing the board is if the microwave will not work at all.
All of the information for this microwave light bulb replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: multi-screwdriver
All of the information for this microwave light bulb replacement video is applicable to the following brands:
Kitchenaid, Whirlpool
Tools used: multi-screwdriver
Step-By-Step Instructions
1
Microwave Oven -Model KMBP100ESS01
2
KitchenAid Built-In Microwave Oven Main Control Board Replacement
3
ATTENTION: TOOLS & ASSISTANCE NEEDED:
4
Step 1: You will need a Phillips-head screwdriver or a quarter-inch nut driver and an assistant to help move heavy microwave.
5
"Step 2: Before you begin, be sure to turn off the power supply to the oven junction box. "
6
Step 3: Open the oven door and remove any racks from the oven along with the turntable and support.
7
Step 4: Now use a Phillips-head screwdriver or quarter-inch nut driver to unthread the two screws securing the mounting flanges to the cabinet.
8
Step 5: Remove the washers as well if still intact.
9
Step 6: Now have an assistant to help you pull the appliance out of the cabinet and set it on a sturdy surface.
10
Step 7: Be aware that if the conduit cable is not long enough to move the microwave oven you will need to disconnect the power and grounding wires and remove the conduit cable from the junction box.
11
Step 8: Use a Phillips-head screwdriver or a quarter-inch nut driver to unthread the four screws securing the top access panel.
12
Step 9: Lift the panel up then slide forward to remove.
13
"Step 10: Note the orientation of the wires connected to the main control board, then disconnect them. "
14
Step 11: Pull the front and side retaining tabs back to release the old board.
15
Step 12: Install the new control board by first positioning the rear edge under the tabs then secure the board under the front and side tabs.
16
Step 13: Connect the wires to the appropriate terminals on the new board.
17
Step 14: Replace the top access panel by inserting the rear edge first.
18
Step 15: Connect the wires to the appropriate terminals on the new board.
19
Step 16: Replace the top access panel by inserting the rear edge first.
20
Step 17: Secure it with the screws.
21
"Step 18: With an assistant, return the microwave oven to the cabinet and push it into position. "
22
Step 19: Insert the washers into the holes in the flanges then thread the two screws to secure the flanges to the cabinet.
23
Step 20: Replace the support and align the turntable on the coupling.
24
Step 21: Turn on the power supply back on to the microwave.
25
Congrats! Your microwave oven is ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com