Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Convection Gas Range Broil Element Replacement #W10552502 
KitchenAid Convection Gas Range Broil Element Replacement #W10552502
Skill Level
Total Parts Cost
$84.33Estimated Savings
$112.5005:19
- Description
This video provides step-by-step repair instructions for replacing the broil element on a Kitchenaid Gas Convection Range (model #KSGB900ESS01). The most common reason for replacing the element is if the broiler is not working.
This element replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This element replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Before you replace the broil element in your gas range,
2
Be sure to unplug the power cord or shut off the power supply.
3
Shut off the gas supply as well.
4
Pull the range away from the wall so you can access the rear of the appliance.
5
Using a Phillips head screwdriver, unthread the two screws securing the lower rear access panel.
6
Lift the panel up and out to remove.
7
Unthread the three screws to release the left side stop bracket.
8
Repeat to detach the right side bracket.
9
Now lift the upper rear access panel up to remove.
10
Disconnect the wires from the broil element terminals.
11
Now fully open the oven door and rotate both door hinge locks back.
12
Partially close the door, then lift and pull the door toward you to remove.
13
With the handle side down, set the door on a blanket.
14
Slide out the oven racks.
15
Unthread the front screws securing the broiler tube and shield.
16
Remove the shield, then disconnect the broil element's spark electrode wire and set the broiler tube assembly aside.
17
Now unthread the two rear screws securing the broil element to the back of the oven, and you can fully remove the old element.
18
Install the new broil element by inserting the terminals through the holes in the back of the oven.
19
Temporarily replace the front screw to help support the element.
20
Thread and tighten the rear screws.
21
Now unthread the front screw.
22
Next, reconnect the broil spark electrode wire, align the shield, and reposition the broiler tube assembly.
23
Rethread and tighten the front screw to secure.
24
Slide the oven racks into place.
25
Reinstall the oven door by inserting the door hinges into the hinge slots at a 45-degree angle.
26
Lower the door to its fully open position, then rotate the hinge locks forward.
27
Returning to the rear of the appliance, connect the wires to the broil element terminals.
28
Reinstall the upper rear access panel by hooking it on the tabs.
29
Realign the two stop brackets and thread the screws to hold them in place.
30
Reinstall the lower access panel by inserting the tabs in the slots first.
31
Lower the panel and secure it with the screws.
32
Turn the gas supply back on.
33
Plug the power cord back in or restore the power supply, and the gas range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the broil element on a Kitchenaid Gas Convection Range (model #KSGB900ESS01). The most common reason for replacing the element is if the broiler is not working.
This element replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This element replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Before you replace the broil element in your gas range,
2
Be sure to unplug the power cord or shut off the power supply.
3
Shut off the gas supply as well.
4
Pull the range away from the wall so you can access the rear of the appliance.
5
Using a Phillips head screwdriver, unthread the two screws securing the lower rear access panel.
6
Lift the panel up and out to remove.
7
Unthread the three screws to release the left side stop bracket.
8
Repeat to detach the right side bracket.
9
Now lift the upper rear access panel up to remove.
10
Disconnect the wires from the broil element terminals.
11
Now fully open the oven door and rotate both door hinge locks back.
12
Partially close the door, then lift and pull the door toward you to remove.
13
With the handle side down, set the door on a blanket.
14
Slide out the oven racks.
15
Unthread the front screws securing the broiler tube and shield.
16
Remove the shield, then disconnect the broil element's spark electrode wire and set the broiler tube assembly aside.
17
Now unthread the two rear screws securing the broil element to the back of the oven, and you can fully remove the old element.
18
Install the new broil element by inserting the terminals through the holes in the back of the oven.
19
Temporarily replace the front screw to help support the element.
20
Thread and tighten the rear screws.
21
Now unthread the front screw.
22
Next, reconnect the broil spark electrode wire, align the shield, and reposition the broiler tube assembly.
23
Rethread and tighten the front screw to secure.
24
Slide the oven racks into place.
25
Reinstall the oven door by inserting the door hinges into the hinge slots at a 45-degree angle.
26
Lower the door to its fully open position, then rotate the hinge locks forward.
27
Returning to the rear of the appliance, connect the wires to the broil element terminals.
28
Reinstall the upper rear access panel by hooking it on the tabs.
29
Realign the two stop brackets and thread the screws to hold them in place.
30
Reinstall the lower access panel by inserting the tabs in the slots first.
31
Lower the panel and secure it with the screws.
32
Turn the gas supply back on.
33
Plug the power cord back in or restore the power supply, and the gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
09:43
Part Replacement
KitchenAid Convection Gas Range Cooling Fan Assembly Replacement #W11107275
08:32
Part Replacement
KitchenAid Convection Gas Range Main Control Board Replacement #W11100100
05:52
Part Replacement
KitchenAid Convection Gas Range Control Panel Replacement #W10913685
07:53
Part Replacement
KitchenAid Convection Gas Range Right Rear Burner Spark Electrode Replacement #W11220383
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com