Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Convection Gas Range Oven Spark Module Replacement #W10860916 
KitchenAid Convection Gas Range Oven Spark Module Replacement #W10860916
Skill Level
Total Parts Cost
$205.54Estimated Savings
$112.5003:34
- Description
This video provides step-by-step repair instructions for replacing the oven spark module on a Kitchenaid Gas Convection Range (model #KSGB900ESS01). The most common reason for replacing the module is if the oven will not light and heat.
This module replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This module replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Convection gas range - ksgb900ess1
2
Kitchenaid convection gas range - Oven Spark Module Replacement
3
You will need a phillips-head screwdriver to complete this repair.
4
Shock
5
BE SURE TO UNPLUG THE POWER CORD OR SHUT OFF THE POWER SUPPLY.
6
PULL THE RANGE AWAY FROM THE WALL SO YOU CAN ACCESS THE REAR OF THE APPLIANCE.
7
USING A PHILLIPS-HEAD SCREWDRIVER, UNTHREAD THE TWO SCREWS SECURING THE LOWER REAR ACCESS PANEL.
8
Sharp
9
Lift the panel up and out to remove.
10
Unthread the three screws to release the left side stop bracket.
11
Repeat to detach the right side bracket.
12
Now lift the upper rear access panel up to remove.
13
Disconnect the control board wire harness from the oven spark module board.
14
Note the orientation of the bake and broil spark wires, then disconnect them, along with the grounding wire.
15
For better access to remove the board, unthread the screws to release the cover.
16
Now unthread the mounting screw and lift the old board straight up to remove.
17
Install the new spark module board, by aligning the four mounting studs in the slots on the back panel.
18
Thread the mounting screw to secure.
19
Replace the cover if applicable.
20
Connect the bake and broil spark wires to the appropriate terminals on the new board.
21
Connect the control board wire harness and the grounding wire as well.
22
Reinstall the upper rear access panel by hooking it on the tabs.
23
Realign the two stop brackets and thread the screws to hold them in place.
24
Reinstall the lower access panel by inserting the tabs in the slots first.
25
Lower the panel and secure it with the screws.
26
Plug the power cord back in or restore the power supply.
Description
This video provides step-by-step repair instructions for replacing the oven spark module on a Kitchenaid Gas Convection Range (model #KSGB900ESS01). The most common reason for replacing the module is if the oven will not light and heat.
This module replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This module replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Convection gas range - ksgb900ess1
2
Kitchenaid convection gas range - Oven Spark Module Replacement
3
You will need a phillips-head screwdriver to complete this repair.
4
Shock
5
BE SURE TO UNPLUG THE POWER CORD OR SHUT OFF THE POWER SUPPLY.
6
PULL THE RANGE AWAY FROM THE WALL SO YOU CAN ACCESS THE REAR OF THE APPLIANCE.
7
USING A PHILLIPS-HEAD SCREWDRIVER, UNTHREAD THE TWO SCREWS SECURING THE LOWER REAR ACCESS PANEL.
8
Sharp
9
Lift the panel up and out to remove.
10
Unthread the three screws to release the left side stop bracket.
11
Repeat to detach the right side bracket.
12
Now lift the upper rear access panel up to remove.
13
Disconnect the control board wire harness from the oven spark module board.
14
Note the orientation of the bake and broil spark wires, then disconnect them, along with the grounding wire.
15
For better access to remove the board, unthread the screws to release the cover.
16
Now unthread the mounting screw and lift the old board straight up to remove.
17
Install the new spark module board, by aligning the four mounting studs in the slots on the back panel.
18
Thread the mounting screw to secure.
19
Replace the cover if applicable.
20
Connect the bake and broil spark wires to the appropriate terminals on the new board.
21
Connect the control board wire harness and the grounding wire as well.
22
Reinstall the upper rear access panel by hooking it on the tabs.
23
Realign the two stop brackets and thread the screws to hold them in place.
24
Reinstall the lower access panel by inserting the tabs in the slots first.
25
Lower the panel and secure it with the screws.
26
Plug the power cord back in or restore the power supply.
Applicable Product Model
Related Articles & Videos
09:43
Part Replacement
KitchenAid Convection Gas Range Cooling Fan Assembly Replacement #W11107275
08:32
Part Replacement
KitchenAid Convection Gas Range Main Control Board Replacement #W11100100
05:52
Part Replacement
KitchenAid Convection Gas Range Control Panel Replacement #W10913685
07:53
Part Replacement
KitchenAid Convection Gas Range Right Rear Burner Spark Electrode Replacement #W11220383
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com