Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Convection Gas Range Power Cord Replacement #W10889764 
KitchenAid Convection Gas Range Power Cord Replacement #W10889764
Skill Level
Total Parts Cost
$79.23Estimated Savings
$112.5009:30
- Description
This video provides step-by-step repair instructions for replacing the power cord on a Kitchenaid Gas Convection Range (model #KSGB900ESS01). The most common reason for replacing the cord is if the range will not power up at all.
This cord replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This cord replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
Convection gas range - ksgb900ess1
2
Kitchenaid convection gas range - Power Cord Replacement
3
You will need a phillips-head screwdriver, pliers, and a flat-head screwdriver to complete this repair.
4
Shock
5
BE SURE THE OLD CORD IS UNPLUGGED.
6
Fire
7
HUT OFF THE GAS SUPPLY.
8
PULL THE RANGE AWAY FROM THE WALL SO YOU CAN ACCESS THE REAR OF THE APPLIANCE.
9
OPEN THE OVEN DOOR AND USE A PHILLIPS-HEAD SCREWDRIVER TO UNTHREAD THE SCREWS SECURING THE CONTROL PANEL?S LOWER COVER.
10
Sharp
11
REMOVE THE COVER.
12
PULL OFF THE FIVE CONTROL KNOBS.
13
NEXT, UNTHREAD THE TWO SCREWS SECURING THE CONTROL PANEL TO THE FRAME.
14
DETACH THE CONTROL PANEL AND SUPPORT IT TO AVOID STRAINING THE WIRES.
15
NOW UNTHREAD THE FRONT BRACKET SCREWS SECURING THE MAIN TOP.
16
UNTHREAD THE TWO SCREWS UNDERNEATH THE REAR CORNERS OF THE TOP.
17
Heavy
18
LIFT OFF BOTH GRATES.
19
REMOVE ALL FIVE BURNER CAPS AND BURNER BASES.
20
YOU CAN NOW UNTHREAD THE SCREWS SECURING THE ORIFICE HOLDERS TO THE MAIN TOP.
21
Sharp
22
WITH THE SCREWS UNTHREADED, YOU CAN LIFT OFF THE TOP.
23
USING THE PHILLIPS-HEAD SCREWDRIVER, UNTHREAD THE TWO SCREWS SECURING THE LOWER REAR ACCESS PANEL.
24
Sharp
25
LIFT THE PANEL UP AND OUT TO REMOVE.
26
UNTHREAD THE THREE SCREWS TO RELEASE THE LEFT SIDE STOP BRACKET.
27
REPEAT TO DETACH THE RIGHT SIDE BRACKET.
28
NOW LIFT THE UPPER REAR ACCESS PANEL UP TO REMOVE.
29
NEXT, UNTHREAD THE TWO SCREWS SECURING THE ORIFICE HOLDER SUPPORT PANEL TO THE RIGHT SIDE PANEL.
30
UNTHREAD THE FOUR REMAINING SCREWS SECURING THE SIDE PANEL.
31
NOW USE A FLAT-HEAD SCREWDRIVER TO DEPRESS THE RETAINING TAB AT THE REAR AND YOU CAN FULLY DETACH THE PANEL.
32
DISCONNECT THE POWER CORD WIRE CONNECTER.
33
UNTHREAD THE SCREW SECURING THE GROUNDING WIRE.
34
USE PLIERS AND A FLAT-HEAD SCREWDRIVER TO HELP DEPRESS THE STRAIN RELIEF TABS TO RELEASE THE OLD CORD.
35
INSTALL THE NEW POWER CORD BY FEEDING THE WIRE CONNECTER THROUGH THE HOLE IN THE BACK PANEL THEN SNAP THE STRAIN RELIEF INTO PLACE.
36
CONNECT THE WIRE CONNECTER.
37
SECURE THE GROUNDING WIRE TO THE BACK PANEL WITH THE SCREW.
38
REINSTALL THE SIDE PANEL BY ALIGNING THE FRAME TABS WITH THE SLOTS ON THE FRONT OF THE PANEL, THEN SNAP THE PANEL INTO POSITION.
39
SECURE IT WITH THE SCREWS.
40
REPLACE THE SCREWS SECURING THE ORIFICE HOLDER SUPPORT PANEL TO THE SIDE PANEL.
41
REINSTALL THE UPPER REAR ACCESS PANEL BY HOOKING IT ON THE TABS.
42
REALIGN THE TWO STOP BRACKETS AND THREAD THE SCREWS TO HOLD THEM IN PLACE.
43
REINSTALL THE LOWER ACCESS PANEL BY INSERTING THE TABS IN THE SLOTS FIRST.
44
LOWER THE PANEL AND SECURE IT WITH THE SCREWS.
45
REPOSITION THE MAIN TOP ON THE FRAME SO THE SPARK ELECTRODES PROTRUDE THROUGH THE HOLES IN THE TOP.
46
CONFIRM THAT THE ORIFICE HOLDERS ARE ALIGNED?THEN THREAD AND TIGHTEN THE SCREWS TO SECURE THE HOLDERS TO THE MAIN TOP.
47
REPLACE EACH BURNER BASE IN ITS PROPER LOCATION BY ALIGNING THE NOTCH IN THE BASE WITH THE SPARK ELECTRODE.
48
REPLACE THE BURNER CAPS.
49
REPOSITION THE GRATES.
50
THREAD THE TWO REAR SCREWS TO SECURE THE MAIN TOP.
51
REPLACE THE FRONT BRACKET SCREWS.
52
REALIGN THE CONTROL PANEL ON THE FRONT BRACKETS.
53
SECURE IT WITH THE SCREWS.
54
REPLACE THE LOWER COVER, THEN THREAD THE SCREWS TO SECURE.
55
REALIGN THE CONTROL KNOBS ON THE VALVE STEMS AND PUSH THEM INTO PLACE ? NOTE THAT THE POWER BURNER CONTROL KNOB SHOULD BE PLACED ON THE SECOND STEM FROM THE LEFT.
56
TURN THE GAS SUPPLY BACK ON.
57
PLUG THE NEW POWER CORD IN.
Description
This video provides step-by-step repair instructions for replacing the power cord on a Kitchenaid Gas Convection Range (model #KSGB900ESS01). The most common reason for replacing the cord is if the range will not power up at all.
This cord replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
This cord replacement video is applicable to the following brands:
Whirlpool, Kitchenaid
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
Convection gas range - ksgb900ess1
2
Kitchenaid convection gas range - Power Cord Replacement
3
You will need a phillips-head screwdriver, pliers, and a flat-head screwdriver to complete this repair.
4
Shock
5
BE SURE THE OLD CORD IS UNPLUGGED.
6
Fire
7
HUT OFF THE GAS SUPPLY.
8
PULL THE RANGE AWAY FROM THE WALL SO YOU CAN ACCESS THE REAR OF THE APPLIANCE.
9
OPEN THE OVEN DOOR AND USE A PHILLIPS-HEAD SCREWDRIVER TO UNTHREAD THE SCREWS SECURING THE CONTROL PANEL?S LOWER COVER.
10
Sharp
11
REMOVE THE COVER.
12
PULL OFF THE FIVE CONTROL KNOBS.
13
NEXT, UNTHREAD THE TWO SCREWS SECURING THE CONTROL PANEL TO THE FRAME.
14
DETACH THE CONTROL PANEL AND SUPPORT IT TO AVOID STRAINING THE WIRES.
15
NOW UNTHREAD THE FRONT BRACKET SCREWS SECURING THE MAIN TOP.
16
UNTHREAD THE TWO SCREWS UNDERNEATH THE REAR CORNERS OF THE TOP.
17
Heavy
18
LIFT OFF BOTH GRATES.
19
REMOVE ALL FIVE BURNER CAPS AND BURNER BASES.
20
YOU CAN NOW UNTHREAD THE SCREWS SECURING THE ORIFICE HOLDERS TO THE MAIN TOP.
21
Sharp
22
WITH THE SCREWS UNTHREADED, YOU CAN LIFT OFF THE TOP.
23
USING THE PHILLIPS-HEAD SCREWDRIVER, UNTHREAD THE TWO SCREWS SECURING THE LOWER REAR ACCESS PANEL.
24
Sharp
25
LIFT THE PANEL UP AND OUT TO REMOVE.
26
UNTHREAD THE THREE SCREWS TO RELEASE THE LEFT SIDE STOP BRACKET.
27
REPEAT TO DETACH THE RIGHT SIDE BRACKET.
28
NOW LIFT THE UPPER REAR ACCESS PANEL UP TO REMOVE.
29
NEXT, UNTHREAD THE TWO SCREWS SECURING THE ORIFICE HOLDER SUPPORT PANEL TO THE RIGHT SIDE PANEL.
30
UNTHREAD THE FOUR REMAINING SCREWS SECURING THE SIDE PANEL.
31
NOW USE A FLAT-HEAD SCREWDRIVER TO DEPRESS THE RETAINING TAB AT THE REAR AND YOU CAN FULLY DETACH THE PANEL.
32
DISCONNECT THE POWER CORD WIRE CONNECTER.
33
UNTHREAD THE SCREW SECURING THE GROUNDING WIRE.
34
USE PLIERS AND A FLAT-HEAD SCREWDRIVER TO HELP DEPRESS THE STRAIN RELIEF TABS TO RELEASE THE OLD CORD.
35
INSTALL THE NEW POWER CORD BY FEEDING THE WIRE CONNECTER THROUGH THE HOLE IN THE BACK PANEL THEN SNAP THE STRAIN RELIEF INTO PLACE.
36
CONNECT THE WIRE CONNECTER.
37
SECURE THE GROUNDING WIRE TO THE BACK PANEL WITH THE SCREW.
38
REINSTALL THE SIDE PANEL BY ALIGNING THE FRAME TABS WITH THE SLOTS ON THE FRONT OF THE PANEL, THEN SNAP THE PANEL INTO POSITION.
39
SECURE IT WITH THE SCREWS.
40
REPLACE THE SCREWS SECURING THE ORIFICE HOLDER SUPPORT PANEL TO THE SIDE PANEL.
41
REINSTALL THE UPPER REAR ACCESS PANEL BY HOOKING IT ON THE TABS.
42
REALIGN THE TWO STOP BRACKETS AND THREAD THE SCREWS TO HOLD THEM IN PLACE.
43
REINSTALL THE LOWER ACCESS PANEL BY INSERTING THE TABS IN THE SLOTS FIRST.
44
LOWER THE PANEL AND SECURE IT WITH THE SCREWS.
45
REPOSITION THE MAIN TOP ON THE FRAME SO THE SPARK ELECTRODES PROTRUDE THROUGH THE HOLES IN THE TOP.
46
CONFIRM THAT THE ORIFICE HOLDERS ARE ALIGNED?THEN THREAD AND TIGHTEN THE SCREWS TO SECURE THE HOLDERS TO THE MAIN TOP.
47
REPLACE EACH BURNER BASE IN ITS PROPER LOCATION BY ALIGNING THE NOTCH IN THE BASE WITH THE SPARK ELECTRODE.
48
REPLACE THE BURNER CAPS.
49
REPOSITION THE GRATES.
50
THREAD THE TWO REAR SCREWS TO SECURE THE MAIN TOP.
51
REPLACE THE FRONT BRACKET SCREWS.
52
REALIGN THE CONTROL PANEL ON THE FRONT BRACKETS.
53
SECURE IT WITH THE SCREWS.
54
REPLACE THE LOWER COVER, THEN THREAD THE SCREWS TO SECURE.
55
REALIGN THE CONTROL KNOBS ON THE VALVE STEMS AND PUSH THEM INTO PLACE ? NOTE THAT THE POWER BURNER CONTROL KNOB SHOULD BE PLACED ON THE SECOND STEM FROM THE LEFT.
56
TURN THE GAS SUPPLY BACK ON.
57
PLUG THE NEW POWER CORD IN.
Applicable Product Model
Related Articles & Videos
09:43
Part Replacement
KitchenAid Convection Gas Range Cooling Fan Assembly Replacement #W11107275
08:32
Part Replacement
KitchenAid Convection Gas Range Main Control Board Replacement #W11100100
05:52
Part Replacement
KitchenAid Convection Gas Range Control Panel Replacement #W10913685
07:53
Part Replacement
KitchenAid Convection Gas Range Right Rear Burner Spark Electrode Replacement #W11220383
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com