Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Gas Range Oven Door Hinge Replacement #WPW10440013 
Whirlpool Gas Range Oven Door Hinge Replacement #WPW10440013
Skill Level
Total Parts Cost
$50.56Estimated Savings
$112.5004:26
- Description
This video provides step-by-step repair instructions for replacing the oven door hinge on a Whirlpool gas range. The most common reason for replacing this part is if the door will not open or close properly.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step By Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Oven Door Hinge Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fully open the oven door and rotate both door hinge locks back.
7
Heavy
8
Partially close the door, then lift and pull the door toward you to remove.
9
With the handle side down, set the door on a sturdy surface.
10
Use a Phillips-head screwdriver to unthread the three screws on the bottom securing the inner and outer door assemblies.
11
Heavy
12
With the screws unthreaded, you can slide the outer door assembly off of the inner panel and set it aside.
13
Now unthread the screws to release the vent trim and handle from the inner panel.
14
Next, remove the screws securing the side door glass bracket covering the hinge you?re replacing.
15
Lift off the bracket.
16
Now unthread the three mounting screws securing the hinge.
17
Pull the old hinge free.
18
Install the new door hinge by positioning it on the inner panel, then thread the screws to secure.
19
Reposition the side bracket and secure it with the screws.
20
Align the handle and trim assembly on the inner door panel and secure it with the screws.
21
Slide the outer oven door assembly into position on the inner panel assembly.
22
Thread and tighten the three screws at the bottom.
23
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
24
Lower the door to its fully open position, then rotate the hinge locks forward.
25
Plug the power cord back in or restore the power supply and the gas range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the oven door hinge on a Whirlpool gas range. The most common reason for replacing this part is if the door will not open or close properly.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step-By-Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Oven Door Hinge Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fully open the oven door and rotate both door hinge locks back.
7
Heavy
8
Partially close the door, then lift and pull the door toward you to remove.
9
With the handle side down, set the door on a sturdy surface.
10
Use a Phillips-head screwdriver to unthread the three screws on the bottom securing the inner and outer door assemblies.
11
Heavy
12
With the screws unthreaded, you can slide the outer door assembly off of the inner panel and set it aside.
13
Now unthread the screws to release the vent trim and handle from the inner panel.
14
Next, remove the screws securing the side door glass bracket covering the hinge you?re replacing.
15
Lift off the bracket.
16
Now unthread the three mounting screws securing the hinge.
17
Pull the old hinge free.
18
Install the new door hinge by positioning it on the inner panel, then thread the screws to secure.
19
Reposition the side bracket and secure it with the screws.
20
Align the handle and trim assembly on the inner door panel and secure it with the screws.
21
Slide the outer oven door assembly into position on the inner panel assembly.
22
Thread and tighten the three screws at the bottom.
23
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
24
Lower the door to its fully open position, then rotate the hinge locks forward.
25
Plug the power cord back in or restore the power supply and the gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com