Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Gas Range Bake Electrode Replacement #WPW10324262 
Whirlpool Gas Range Bake Electrode Replacement #WPW10324262
Skill Level
Total Parts Cost
$77.37Estimated Savings
$112.5003:38
- Description
This video provides step-by-step repair instructions for replacing the bake electrode on a Whirlpool gas range. The most common reason for replacing this part is if the bake burner will not light.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step By Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Bake Electrode Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fire Hazard
7
Shut off the gas supply as well.
8
Fully open the oven door and rotate both door hinge locks back.
9
Heavy
10
Partially close the door, then lift and pull the door toward you to remove.
11
With the handle side down, set the door on a blanket or towel.
12
Remove the oven racks.
13
Use a Phillips-head screwdriver to unthread the two rear mounting screws securing the bottom panel.
14
Sharp
15
Lift the panel up from the back to remove.
16
Next, unthread the front and rear screws securing the bake burner tube.
17
Lift up the tube and disconnect the spark electrode wire to fully remove the burner tube ? be careful not to let the electrode wire slip under the lower panel.
18
Unthread the mounting screws to release the old electrode
19
Install the new bake electrode by aligning it on the burner tube.
20
Thread the screws to hold it in place.
21
Returning to the oven, connect the wire to the electrode.
22
Position the burner tube over the orifice, then thread the front and rear screws to secure.
23
Replace the bottom oven panel by aligning the front edge first, then lower the panel and thread the mounting screws.
24
Replace the oven racks.
25
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
26
Lower the door to its fully open position, then rotate the hinge locks forward.
27
Turn the gas supply back on, plug the power cord back in or restore the power supply and the gas range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the bake electrode on a Whirlpool gas range. The most common reason for replacing this part is if the bake burner will not light.
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
All of the information for this part replacement video is applicable to the following brands:
Whirlpool
Step-By-Step Instructions
1
Whirlpool Gas Range - WFG745H0FS1
2
Gas Range Bake Electrode Replacement
3
Tools needed: Phillips-head screwdriver
4
Shock Hazard
5
Be sure to unplug the power cord or shut off the power supply.
6
Fire Hazard
7
Shut off the gas supply as well.
8
Fully open the oven door and rotate both door hinge locks back.
9
Heavy
10
Partially close the door, then lift and pull the door toward you to remove.
11
With the handle side down, set the door on a blanket or towel.
12
Remove the oven racks.
13
Use a Phillips-head screwdriver to unthread the two rear mounting screws securing the bottom panel.
14
Sharp
15
Lift the panel up from the back to remove.
16
Next, unthread the front and rear screws securing the bake burner tube.
17
Lift up the tube and disconnect the spark electrode wire to fully remove the burner tube ? be careful not to let the electrode wire slip under the lower panel.
18
Unthread the mounting screws to release the old electrode
19
Install the new bake electrode by aligning it on the burner tube.
20
Thread the screws to hold it in place.
21
Returning to the oven, connect the wire to the electrode.
22
Position the burner tube over the orifice, then thread the front and rear screws to secure.
23
Replace the bottom oven panel by aligning the front edge first, then lower the panel and thread the mounting screws.
24
Replace the oven racks.
25
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
26
Lower the door to its fully open position, then rotate the hinge locks forward.
27
Turn the gas supply back on, plug the power cord back in or restore the power supply and the gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
03:46
Part Replacement
KitchenAid Convection Gas Range Bake Spark Electrode Replacement #WPW10333842
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com