Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Barracuda Refrigerator Reservoir Coil Replacement WPW10276792 
Whirlpool Barracuda Refrigerator Reservoir Coil Replacement WPW10276792
Skill Level
Total Parts Cost
$78.39Estimated Savings
$112.5005:34
- Description
This video provides step-by-step repair instructions for replacing the reservoir coil on a Whirlpool Barracuda refrigerator (Model WRS325FDAM04). The most common reason for replacing this part is if the refrigerator is leaking.
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
Step By Step Instructions
1
As with any repair, you should unplug the power cord before beginning
2
Turn off the water supply.
3
To replace the water reservoir coil in your refrigerator first remove the drawers and the lower drawer frames from the refrigerator compartment.
4
Next, pull the lower access panel off.
5
Push the coil through the bushing then pull the dispenser water line forward and disconnect it from the coupler.
6
Be prepared for some water to spill.
7
Now remove the screw to release the water line from the rear access panel.
8
Remove the screws securing the rear panel and pull the panel down and out.
9
Detach the inlet line from the retaining clip.
10
Disconnect the line from the water inlet valve and pull the water lines free.
11
Uninstall the screw securing the old water reservoir coil.
12
Note the orientation of the colors on the water lines and pull the lines out of the refrigerator compartment.
13
You’re now ready to install the new water reservoir coil.
14
Feed the appropriate water lines through the bushing in the refrigerator compartment.
15
Position the reservoir coil on the rear panel and secure it with the screw.
16
Now attach the inlet line to the water inlet valve and secure it under the retaining clip.
17
Feed the dispenser line to the front of the appliance and connect it to the coupler.
18
Now pull out the water lines until the markings are aligned with the top of the bushing.
19
Replace the lower drawer frames and drawers.
20
Turn the water supply back on plug the power cord back in then run water through the dispenser and check to see if there are any leaks in the coupler or water inlet valve.
21
Slide the rear access panel into the track and reinstall the screws to secure.
22
Reposition the water line and secure it with the screw.
23
Complete the procedure by aligning the lower access panel and snapping it into place.
Description
This video provides step-by-step repair instructions for replacing the reservoir coil on a Whirlpool Barracuda refrigerator (Model WRS325FDAM04). The most common reason for replacing this part is if the refrigerator is leaking.
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
Step-By-Step Instructions
1
As with any repair, you should unplug the power cord before beginning
2
Turn off the water supply.
3
To replace the water reservoir coil in your refrigerator first remove the drawers and the lower drawer frames from the refrigerator compartment.
4
Next, pull the lower access panel off.
5
Push the coil through the bushing then pull the dispenser water line forward and disconnect it from the coupler.
6
Be prepared for some water to spill.
7
Now remove the screw to release the water line from the rear access panel.
8
Remove the screws securing the rear panel and pull the panel down and out.
9
Detach the inlet line from the retaining clip.
10
Disconnect the line from the water inlet valve and pull the water lines free.
11
Uninstall the screw securing the old water reservoir coil.
12
Note the orientation of the colors on the water lines and pull the lines out of the refrigerator compartment.
13
You’re now ready to install the new water reservoir coil.
14
Feed the appropriate water lines through the bushing in the refrigerator compartment.
15
Position the reservoir coil on the rear panel and secure it with the screw.
16
Now attach the inlet line to the water inlet valve and secure it under the retaining clip.
17
Feed the dispenser line to the front of the appliance and connect it to the coupler.
18
Now pull out the water lines until the markings are aligned with the top of the bushing.
19
Replace the lower drawer frames and drawers.
20
Turn the water supply back on plug the power cord back in then run water through the dispenser and check to see if there are any leaks in the coupler or water inlet valve.
21
Slide the rear access panel into the track and reinstall the screws to secure.
22
Reposition the water line and secure it with the screw.
23
Complete the procedure by aligning the lower access panel and snapping it into place.
Applicable Product Model
Parts Needed
Reservoir
$78.39
Total$0.00
Related Articles & Videos
04:33
Part Replacement
Whirlpool Barracuda Refrigerator Water Filter Housing Replacement W10862461
01:14
Part Replacement
Whirlpool Barracuda Refrigerator Top Liner LED Replacement WPW10515058
00:53
Part Replacement
Whirlpool Barracuda Refrigerator Meat Drawer Shelf Replacement W11223835
01:19
Part Replacement
Whirlpool Barracuda Refrigerator Crisper Shelf Frame Replacement W10914556
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com