Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairWhirlpool Barracuda Refrigerator Defrost Thermostat Replacement W11084324 
Whirlpool Barracuda Refrigerator Defrost Thermostat Replacement W11084324
Skill Level
Total Parts Cost
$79.75Estimated Savings
$112.5003:17
- Description
This video provides step-by-step repair instructions for replacing the defrost thermostat on a Whirlpool Barracuda refrigerator (Model WRS325FDAM04). The most common reason for replacing this part is if the evaporator is freezing over.
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
Step By Step Instructions
1
Before you replace the defrost thermostat in your refrigerator, be sure to unplug the power cord.
2
Remove the freezer shelves.
3
The top shelves can be removed by moving each support to the center of the mounting hole, then slide the shelf to one side to detach.
4
Slide out the lower bin as well.
5
Use a quarter inch socket or nut driver to unthread the screws securing the rear access panel.
6
You can use a putty knife to help lift up the panel to detach it from the mounting tabs.
7
Pull the panel forward to fully remove.
8
Detach the defrost thermostat from the evaporator tubing.
9
Pull the tab on the bottom of the harness connector to disconnect.
10
Disconnect the heater wire connectors.
11
Detach the evaporator motor wires and the grounding wire.
12
Detach the grounding wire from the evaporator housing as well.
13
Install the new defrost thermostat by first connecting the harness connector.
14
Attach the grounding wire to the evaporator housing.
15
Attach the evaporator motor wires along with the grounding wire.
16
Connect the heater wire connectors.
17
Clip the new thermostat onto the evaporator tubing.
18
Reinstall the access panel by positioning the top edge behind the air duct.
19
Align the slots over the mounting tabs.
20
Make sure the bottom lip of the panel is above the drain pan, then thread and tighten the screws.
21
Replace the lower bin and shelving.
22
Plug the power cord back in and your refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the defrost thermostat on a Whirlpool Barracuda refrigerator (Model WRS325FDAM04). The most common reason for replacing this part is if the evaporator is freezing over.
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
All of the information for this video is applicable to the following brands:
Whirlpool, Maytag, Amana, Kitchenaid, Kenmore
Step-By-Step Instructions
1
Before you replace the defrost thermostat in your refrigerator, be sure to unplug the power cord.
2
Remove the freezer shelves.
3
The top shelves can be removed by moving each support to the center of the mounting hole, then slide the shelf to one side to detach.
4
Slide out the lower bin as well.
5
Use a quarter inch socket or nut driver to unthread the screws securing the rear access panel.
6
You can use a putty knife to help lift up the panel to detach it from the mounting tabs.
7
Pull the panel forward to fully remove.
8
Detach the defrost thermostat from the evaporator tubing.
9
Pull the tab on the bottom of the harness connector to disconnect.
10
Disconnect the heater wire connectors.
11
Detach the evaporator motor wires and the grounding wire.
12
Detach the grounding wire from the evaporator housing as well.
13
Install the new defrost thermostat by first connecting the harness connector.
14
Attach the grounding wire to the evaporator housing.
15
Attach the evaporator motor wires along with the grounding wire.
16
Connect the heater wire connectors.
17
Clip the new thermostat onto the evaporator tubing.
18
Reinstall the access panel by positioning the top edge behind the air duct.
19
Align the slots over the mounting tabs.
20
Make sure the bottom lip of the panel is above the drain pan, then thread and tighten the screws.
21
Replace the lower bin and shelving.
22
Plug the power cord back in and your refrigerator should be ready for use.
Applicable Product Model
Parts Needed
Wire Harness
$79.75
Total$0.00
Related Articles & Videos
04:33
Part Replacement
Whirlpool Barracuda Refrigerator Water Filter Housing Replacement W10862461
01:14
Part Replacement
Whirlpool Barracuda Refrigerator Top Liner LED Replacement WPW10515058
00:53
Part Replacement
Whirlpool Barracuda Refrigerator Meat Drawer Shelf Replacement W11223835
01:19
Part Replacement
Whirlpool Barracuda Refrigerator Crisper Shelf Frame Replacement W10914556
01:38
Part Replacement
Whirlpool Barracuda Refrigerator Beveled LED Replacement WPW10515057
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com