Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairEcho Leaf Blower Intake Grid Replacement (E104000250)
Echo Leaf Blower Intake Grid Replacement (E104000250)
Skill Level
Total Parts Cost
$10.56Estimated Savings
$112.5005:43
- Description
This video provides step-by-step instructions for replacing the intake grid on Echo leaf blowers.
Step By Step Instructions
1
Leaf Blower- Model PB580T
2
Leaf Blower Air Intake Grid Replacement
3
"Step 1: Make sure the engine has cooled and the on/off switch is in the ""off"" switch. "
4
Step 2: Perform this procedure with little or no fuel in the tank.
5
"Step 3: Set the leaf blower on its side.
"
6
Step 4: Use a T-27 Torx bit to unthread the four screws securing the fuel tank retainer.
7
Step 5: Set the fuel tank and retainer aside.
8
Step 6: Unthread the nine screws securing the two halves of the blower housing.
9
Step 7: Detach the cable and static discharge wire from the housing retaining clip.
10
Step 8: Unthread the screw to fully release the discharge wire from the engine.
11
Step 9: Separate the two halves of the blower housing.
12
Step 10: Detach the elbow blower tube and set the frame upright.
13
Step 11: Unsnap the foam pad.
14
Step 12: Unthread the four screws securing the fan cover.
15
Step 13: Unthread the safety strap screw to fully release the cover.
16
Step 14: Use pliers to depress the retaining clips at the top and bottom of the frame to detach the air intake grid.
17
Step 15: Use a quarter-inch deep-well socket to release the side retaining tabs to fully remove the old grid.
18
Step 16: Install the new air intake grid by aligning the tabs and clips then snap the grid into position.
19
Step 17: Reinstall the fan cover by first threading the screw to secure the safety strap to the cover.
20
Step 18: Reposition the cover and thread the four screws.
21
Step 19: Snap the foam pad into place.
22
Step 20: Lay the frame back down and position the elbow blower tube.
23
Step 21: Rejoin the two halves of the blower housing.
24
Step 22: Rethread the screw to secure the static discharge wire to the engine.
25
Step 23: Secure the discharge wire and the cable in the housing retaining clip.
26
Step 24: Rethread all of the screws to secure the two halves of the blower housing.
27
Step 25: Realign the retainer on the fuel tank then reposition the assembly on the frame.
28
"Step 26: Confirm the washers are in place on the screws then thread the four screws to secure the retainer.
"
29
Step 27: Refill the fuel tank if necessary.
30
Congratulations! Your leaf blower should be ready for use.
Description
This video provides step-by-step instructions for replacing the intake grid on Echo leaf blowers.
Step-By-Step Instructions
1
Leaf Blower- Model PB580T
2
Leaf Blower Air Intake Grid Replacement
3
"Step 1: Make sure the engine has cooled and the on/off switch is in the ""off"" switch. "
4
Step 2: Perform this procedure with little or no fuel in the tank.
5
"Step 3: Set the leaf blower on its side.
"
6
Step 4: Use a T-27 Torx bit to unthread the four screws securing the fuel tank retainer.
7
Step 5: Set the fuel tank and retainer aside.
8
Step 6: Unthread the nine screws securing the two halves of the blower housing.
9
Step 7: Detach the cable and static discharge wire from the housing retaining clip.
10
Step 8: Unthread the screw to fully release the discharge wire from the engine.
11
Step 9: Separate the two halves of the blower housing.
12
Step 10: Detach the elbow blower tube and set the frame upright.
13
Step 11: Unsnap the foam pad.
14
Step 12: Unthread the four screws securing the fan cover.
15
Step 13: Unthread the safety strap screw to fully release the cover.
16
Step 14: Use pliers to depress the retaining clips at the top and bottom of the frame to detach the air intake grid.
17
Step 15: Use a quarter-inch deep-well socket to release the side retaining tabs to fully remove the old grid.
18
Step 16: Install the new air intake grid by aligning the tabs and clips then snap the grid into position.
19
Step 17: Reinstall the fan cover by first threading the screw to secure the safety strap to the cover.
20
Step 18: Reposition the cover and thread the four screws.
21
Step 19: Snap the foam pad into place.
22
Step 20: Lay the frame back down and position the elbow blower tube.
23
Step 21: Rejoin the two halves of the blower housing.
24
Step 22: Rethread the screw to secure the static discharge wire to the engine.
25
Step 23: Secure the discharge wire and the cable in the housing retaining clip.
26
Step 24: Rethread all of the screws to secure the two halves of the blower housing.
27
Step 25: Realign the retainer on the fuel tank then reposition the assembly on the frame.
28
"Step 26: Confirm the washers are in place on the screws then thread the four screws to secure the retainer.
"
29
Step 27: Refill the fuel tank if necessary.
30
Congratulations! Your leaf blower should be ready for use.
Applicable Product Model
Parts Needed
Air Grille
$10.56
Total$0.00
Related Articles & Videos
05:34
Part Replacement
Echo Leaf Blower Throttle Control Assembly Replacement (P021052251)
02:41
Part Replacement
Echo Backpack Leaf Blower Fuel Tank Grommet Replacement (13211555930)
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com