Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Electric Range Broil Element Replacement (316203301)
Frigidaire Electric Range Broil Element Replacement (316203301)
Skill Level
Total Parts Cost
$149.28Estimated Savings
$112.5004:48
- Description
This video provides step-by-step instructions for replacing the broil element on Frigidaire electric ranges.
All of the information in this video is applicable to the following brands: Frigidaire
All of the information in this video is applicable to the following brands: Frigidaire
Step By Step Instructions
1
Frigidaire Electric Range - Model LFEF3054TFG
2
Electric Range Broil Element Replacement
3
Tools & Assistance Needed
4
"You will need a quarter-inch socket or nut driver for this procedure, and you may need assistance."
5
Be sure to unplug the power cord or shut off the power supply.
6
Have an assistant help you to move the range away from the wall.
7
Use a quarter-inch socket or nut driver to unthread the screws to release the upper rear access panel.
8
Unthread the bottom screw securing the lower access panel to the power cord retaining plate.
9
Unthread the four remaining mounting screws securing the panel.
10
Pull the panel up to remove.
11
Disconnect the wires from the broil element terminals.
12
Fully open the oven door and rotate both door hinge locks back.
13
"Partially close the door, then lift and pull the door toward you to remove."
14
Slide out the oven racks.
15
"Using a quarter-inch socket or nut driver, unthread the rear screws securing the broil element."
16
Unthread the two screws securing the wire retainers.
17
Set the retainers aside and pull the old element forward to remove.
18
Install the new broil element by inserting the terminals through the holes in the rear panel.
19
Replace the wire retainers and thread the screws to secure.
20
Thread the rear screws.
21
Replace the oven racks.
22
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
23
"Lower the door to its fully open position, then rotate the hinge locks forward."
24
"Returning to the rear of the appliance, connect the wires to the broil element terminals."
25
"Reinstall the lower access panel by aligning the power cord retaining plate with the slots in the panel, then hook the bottom tabs on the frame, fully position the panel and thread the four side screws."
26
Replace the bottom screw to secure the panel to the power cord retaining plate.
27
Realign the upper access panel by placing the panel tabs behind the lip of the control panel.
28
Thread the screws.
29
Move the appliance back against the wall.
30
Plug the power cord back in or restore the power supply.
31
Congrats! Your electric range is ready for use.
Description
This video provides step-by-step instructions for replacing the broil element on Frigidaire electric ranges.
All of the information in this video is applicable to the following brands: Frigidaire
All of the information in this video is applicable to the following brands: Frigidaire
Step-By-Step Instructions
1
Frigidaire Electric Range - Model LFEF3054TFG
2
Electric Range Broil Element Replacement
3
Tools & Assistance Needed
4
"You will need a quarter-inch socket or nut driver for this procedure, and you may need assistance."
5
Be sure to unplug the power cord or shut off the power supply.
6
Have an assistant help you to move the range away from the wall.
7
Use a quarter-inch socket or nut driver to unthread the screws to release the upper rear access panel.
8
Unthread the bottom screw securing the lower access panel to the power cord retaining plate.
9
Unthread the four remaining mounting screws securing the panel.
10
Pull the panel up to remove.
11
Disconnect the wires from the broil element terminals.
12
Fully open the oven door and rotate both door hinge locks back.
13
"Partially close the door, then lift and pull the door toward you to remove."
14
Slide out the oven racks.
15
"Using a quarter-inch socket or nut driver, unthread the rear screws securing the broil element."
16
Unthread the two screws securing the wire retainers.
17
Set the retainers aside and pull the old element forward to remove.
18
Install the new broil element by inserting the terminals through the holes in the rear panel.
19
Replace the wire retainers and thread the screws to secure.
20
Thread the rear screws.
21
Replace the oven racks.
22
Reinstall the oven door by inserting the door hinges into the hinge slots at a forty-five degree angle.
23
"Lower the door to its fully open position, then rotate the hinge locks forward."
24
"Returning to the rear of the appliance, connect the wires to the broil element terminals."
25
"Reinstall the lower access panel by aligning the power cord retaining plate with the slots in the panel, then hook the bottom tabs on the frame, fully position the panel and thread the four side screws."
26
Replace the bottom screw to secure the panel to the power cord retaining plate.
27
Realign the upper access panel by placing the panel tabs behind the lip of the control panel.
28
Thread the screws.
29
Move the appliance back against the wall.
30
Plug the power cord back in or restore the power supply.
31
Congrats! Your electric range is ready for use.
Applicable Product Model
Related Articles & Videos
02:56
Part Replacement
Frigidaire Electric Range Outer Oven Door Glass Replacement (316452758)
03:57
Part Replacement
Frigidaire Electric Range Main Top Assembly Replacement (5304513244)
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com