Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Gas Range Right Rear Burner Orifice Holder Replacement (316536610)
Frigidaire Gas Range Right Rear Burner Orifice Holder Replacement (316536610)
Skill Level
Total Parts Cost
$81.35Estimated Savings
$112.5005:25
- Description
This video provides step-by-step instructions for replacing the right rear burner orifice holder on Frigidaire gas ranges.
All of the information in this video is applicable to the following brands: Frigidaire
Tools used: 3/16th-inch socket or nut driver, quarter-inch socket or nut driver & Phillips-head screwdriver, & a half-inch wrench.
All of the information in this video is applicable to the following brands: Frigidaire
Tools used: 3/16th-inch socket or nut driver, quarter-inch socket or nut driver & Phillips-head screwdriver, & a half-inch wrench.
Step By Step Instructions
1
Before you replace the right rear burner orifice holder in your gas range,
2
Be sure to unplug the power cord or shut off the power supply.
3
Shut off the gas supply as well.
4
Lift off the three grates, remove all of the burner caps, and lift the center burner base straight up to remove.
5
Using a 3/16 inch socket or nut driver, unthread the mounting screws securing the front and rear burner bases.
6
With the screws on threaded, lift each base straight up to remove.
7
Next, use a quarter inch socket or nut driver to unthread all of the screws securing the officeholders to the main top.
8
Pull off the control knobs.
9
You can use string or wire to help pry them off.
10
Open the oven door and use a Phillips head screwdriver to unthread the two mounting screws securing the valve control panel.
11
Remove the panel.
12
Unthread the two screws securing the main top.
13
You can now pull the main top forward and lift up to remove.
14
Disconnect the wire from the igniter.
15
Use a half-inch wrench to unthread the nut to release the old orphis holder.
16
Install the new office holder by inserting the gas supply tube into the valve, then thread the nut.
17
Avoid over-tightening the nut.
18
Connect the wire to the igniter.
19
Reinstall the main top by aligning the rear edge under the retaining tabs.
20
Confirm that the office holders and igniters protrude through the holes in the top.
21
Thread the two screws to secure.
22
Reinstall the valve control panel by aligning the slots at the top with the bracket tabs, then thread the mounting screws.
23
Replace the control knobs.
24
Thread all of the screws to secure the office holders to the main top.
25
Reposition the burner bases so the igniter aligns with the notch in the base.
26
Thread the mounting screws to secure the front and rear bases.
27
Realign all the burner caps.
28
Reinstall the grates.
29
Turn the gas supply back on.
30
Plug the power cord back in or restore the power supply, and your gas range should be ready for use.
Description
This video provides step-by-step instructions for replacing the right rear burner orifice holder on Frigidaire gas ranges.
All of the information in this video is applicable to the following brands: Frigidaire
Tools used: 3/16th-inch socket or nut driver, quarter-inch socket or nut driver & Phillips-head screwdriver, & a half-inch wrench.
All of the information in this video is applicable to the following brands: Frigidaire
Tools used: 3/16th-inch socket or nut driver, quarter-inch socket or nut driver & Phillips-head screwdriver, & a half-inch wrench.
Step-By-Step Instructions
1
Before you replace the right rear burner orifice holder in your gas range,
2
Be sure to unplug the power cord or shut off the power supply.
3
Shut off the gas supply as well.
4
Lift off the three grates, remove all of the burner caps, and lift the center burner base straight up to remove.
5
Using a 3/16 inch socket or nut driver, unthread the mounting screws securing the front and rear burner bases.
6
With the screws on threaded, lift each base straight up to remove.
7
Next, use a quarter inch socket or nut driver to unthread all of the screws securing the officeholders to the main top.
8
Pull off the control knobs.
9
You can use string or wire to help pry them off.
10
Open the oven door and use a Phillips head screwdriver to unthread the two mounting screws securing the valve control panel.
11
Remove the panel.
12
Unthread the two screws securing the main top.
13
You can now pull the main top forward and lift up to remove.
14
Disconnect the wire from the igniter.
15
Use a half-inch wrench to unthread the nut to release the old orphis holder.
16
Install the new office holder by inserting the gas supply tube into the valve, then thread the nut.
17
Avoid over-tightening the nut.
18
Connect the wire to the igniter.
19
Reinstall the main top by aligning the rear edge under the retaining tabs.
20
Confirm that the office holders and igniters protrude through the holes in the top.
21
Thread the two screws to secure.
22
Reinstall the valve control panel by aligning the slots at the top with the bracket tabs, then thread the mounting screws.
23
Replace the control knobs.
24
Thread all of the screws to secure the office holders to the main top.
25
Reposition the burner bases so the igniter aligns with the notch in the base.
26
Thread the mounting screws to secure the front and rear bases.
27
Realign all the burner caps.
28
Reinstall the grates.
29
Turn the gas supply back on.
30
Plug the power cord back in or restore the power supply, and your gas range should be ready for use.
Applicable Product Model
Related Articles & Videos
01:25
Part Replacement
Frigidaire Gas Range Right Front Burner Base Replacement (316438400)
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com