Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Front-Load Washer Dispenser Valve Gasket Replacement (part 134371300)
Electrolux Front-Load Washer Dispenser Valve Gasket Replacement (part 134371300)
Skill Level
Total Parts Cost
$46.25Estimated Savings
$112.5004:12
- Description
This video provides step-by-step instructions for replacing the dispenser valve gasket on Electrolux washing machine.
All of the information in this dispenser valve gasket replacement video is applicable to the following brands: Electrolux
Tools used: Phillips-head screwdriver or Number two square drive bit, & a small flat-head screwdriver.
All of the information in this dispenser valve gasket replacement video is applicable to the following brands: Electrolux
Tools used: Phillips-head screwdriver or Number two square drive bit, & a small flat-head screwdriver.
Step By Step Instructions
1
Electrolux Front-Load Washer - Model EFLS627UTT
2
Front-Load Washer Dispenser Valve Gasket Replacement
3
Tools & Assistance Needed
4
"You will need a Philips-head screwdriver and a small flat-head screwdriver for this procedure, and you may need assistance."
5
Be sure to unplug the power cord…
6
Be sure to shut off the water supply.
7
Remove the hot-and-cold water supply lines from the inlet valve ports – be prepared for some water to spill.
8
Have an assistant help you to move the appliance away from the wall.
9
"Using a Philips-head screwdriver or a number two square drive bit, unthread the rear screws securing the top panel."
10
Remove the panel.
11
Unthread the screws securing the vibration damper.
12
Set the damper aside.
13
Disconnect the wire connecters from the water valve assembly.
14
Unthread the three mounting screws securing the valve.
15
"Using a small flat-head screwdriver, depress the tabs to release the valve port bezel."
16
"Pull the valve assembly out of the dispenser, and, if still intact, remove the old gasket."
17
Install the new dispenser valve gasket by sliding it onto the port.
18
"Insert the valve assembly inlet ports through the holes in the rear panel, align the valve gaskets with the dispenser and push the assembly into place."
19
Thread the three mounting screws.
20
Snap the valve port bezel into place.
21
"Connect the wire connecters, then reinstall the vibration damper."
22
Realign the top panel and secure it with the screws at the rear.
23
Move the appliance back against the wall.
24
Attach the hot- and-cold water supply lines to the inlet valve ports.
25
Turn the water supply back on and plug the power cord back in.
26
Congrats! Your front-load washer is ready for use.
Description
This video provides step-by-step instructions for replacing the dispenser valve gasket on Electrolux washing machine.
All of the information in this dispenser valve gasket replacement video is applicable to the following brands: Electrolux
Tools used: Phillips-head screwdriver or Number two square drive bit, & a small flat-head screwdriver.
All of the information in this dispenser valve gasket replacement video is applicable to the following brands: Electrolux
Tools used: Phillips-head screwdriver or Number two square drive bit, & a small flat-head screwdriver.
Step-By-Step Instructions
1
Electrolux Front-Load Washer - Model EFLS627UTT
2
Front-Load Washer Dispenser Valve Gasket Replacement
3
Tools & Assistance Needed
4
"You will need a Philips-head screwdriver and a small flat-head screwdriver for this procedure, and you may need assistance."
5
Be sure to unplug the power cord…
6
Be sure to shut off the water supply.
7
Remove the hot-and-cold water supply lines from the inlet valve ports – be prepared for some water to spill.
8
Have an assistant help you to move the appliance away from the wall.
9
"Using a Philips-head screwdriver or a number two square drive bit, unthread the rear screws securing the top panel."
10
Remove the panel.
11
Unthread the screws securing the vibration damper.
12
Set the damper aside.
13
Disconnect the wire connecters from the water valve assembly.
14
Unthread the three mounting screws securing the valve.
15
"Using a small flat-head screwdriver, depress the tabs to release the valve port bezel."
16
"Pull the valve assembly out of the dispenser, and, if still intact, remove the old gasket."
17
Install the new dispenser valve gasket by sliding it onto the port.
18
"Insert the valve assembly inlet ports through the holes in the rear panel, align the valve gaskets with the dispenser and push the assembly into place."
19
Thread the three mounting screws.
20
Snap the valve port bezel into place.
21
"Connect the wire connecters, then reinstall the vibration damper."
22
Realign the top panel and secure it with the screws at the rear.
23
Move the appliance back against the wall.
24
Attach the hot- and-cold water supply lines to the inlet valve ports.
25
Turn the water supply back on and plug the power cord back in.
26
Congrats! Your front-load washer is ready for use.
Related Articles & Videos
07:53
Part Replacement
Electrolux Front-Load Washer Door Boot Seal Replacement (part 5304505004)
08:08
Part Replacement
Electrolux Front-Load Washer Sump Filter Replacement (part 5304505165)
06:59
Part Replacement
Electrolux Front-Load Washer Drain Pump Assembly Replacement (part 5304514775)
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com