Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairCub Cadet Chipper Shredder Flail Blade Replacement (719-04308)
Cub Cadet Chipper Shredder Flail Blade Replacement (719-04308)
Skill Level
Total Parts Cost
$20.59Estimated Savings
$112.5010:44
- Description
This video provides step-by-step instructions for replacing the flail blade on a Cub Cadet Chipper Shredder. The most common reason to replace this part is if the chipper is not cutting properly.
All of the information in this video is applicable to the following brands: Cub Cadet
All of the information in this video is applicable to the following brands: Cub Cadet
Step By Step Instructions
1
Cub Cadet Chipper Shredder - 24A424M710
2
Chipper Shredder Chipper Blade Replacement
3
"Sharp, Spill, Hot, Heavy"
4
"You will need a 3/8th inch socket, a 7/16th inch socket and wrench, needle-nose pliers, a half-inch wrench, a 3/16th inch allen wrench and a torque wrench"
5
"Using the 3/8th inch socket, unthread the two mounting bolts securing the chute support"
6
Use the half-inch wrench to fully unthread the two mounting nuts securing the chute
7
Heavy
8
Loosen the lower nut and fully remove the chute assembly
9
Unthread the two retaining knob screws securing the bottom of the discharge chute
10
Use the 7/16th inch wrench to secure the mounting bolt and the 7/16th inch socket to fully unthread the nut
11
"Slide out the bolt, detach the chute, and remove the two spacers"
12
Use the needle-nose pliers to pull out the cotter pin and then the screen pin
13
Sharp
14
Lift up the shredder screen and support it
15
Heavy
16
Use the half-inch wrench and the 3/16th inch allen wrench to remove the two mounting bolts and nuts securing the blade
17
Set the old blade aside
18
"Insert one of the mounting bolts and, with the sharp edge facing downward, align the blade on the impeller"
19
Slide the washer over the bolt and thread the nut
20
Sharp
21
"Using the half-inch socket on a torque wrench, tighten the nuts to 25 foot pounds"
22
Release the support and lower the shredder screen
23
Slide the shredder screen pin through the impeller and screen and insert the cotter pin
24
Realign the discharge chute on the impeller housing and insert the spacers
25
Insert the mounting bolt then thread and tighten the nut
26
"Fully position the chute, then thread and tighten the retaining knob screws"
27
Reinstall the chute assembly by sliding it onto the lower mounting bolt behind the washer and nut then align it on the upper bolts
28
Thread and tighten the bolts to secure the support to the base
29
Position the shredder screen mounting post in the hole in the inner flair housing then realign the outer housing
30
Rethread the two upper mounting screws using the speed clips
31
Slide the shredder screen pin through the impeller and screen and insert the cotter pin
32
"Insert the mounting bolt, then thread and tighten the nut"
33
Realign the shredder plate on the impeller housing bolts
34
Thread and tighten all eight mounting nuts to secure
Description
This video provides step-by-step instructions for replacing the flail blade on a Cub Cadet Chipper Shredder. The most common reason to replace this part is if the chipper is not cutting properly.
All of the information in this video is applicable to the following brands: Cub Cadet
All of the information in this video is applicable to the following brands: Cub Cadet
Step-By-Step Instructions
1
Cub Cadet Chipper Shredder - 24A424M710
2
Chipper Shredder Chipper Blade Replacement
3
"Sharp, Spill, Hot, Heavy"
4
"You will need a 3/8th inch socket, a 7/16th inch socket and wrench, needle-nose pliers, a half-inch wrench, a 3/16th inch allen wrench and a torque wrench"
5
"Using the 3/8th inch socket, unthread the two mounting bolts securing the chute support"
6
Use the half-inch wrench to fully unthread the two mounting nuts securing the chute
7
Heavy
8
Loosen the lower nut and fully remove the chute assembly
9
Unthread the two retaining knob screws securing the bottom of the discharge chute
10
Use the 7/16th inch wrench to secure the mounting bolt and the 7/16th inch socket to fully unthread the nut
11
"Slide out the bolt, detach the chute, and remove the two spacers"
12
Use the needle-nose pliers to pull out the cotter pin and then the screen pin
13
Sharp
14
Lift up the shredder screen and support it
15
Heavy
16
Use the half-inch wrench and the 3/16th inch allen wrench to remove the two mounting bolts and nuts securing the blade
17
Set the old blade aside
18
"Insert one of the mounting bolts and, with the sharp edge facing downward, align the blade on the impeller"
19
Slide the washer over the bolt and thread the nut
20
Sharp
21
"Using the half-inch socket on a torque wrench, tighten the nuts to 25 foot pounds"
22
Release the support and lower the shredder screen
23
Slide the shredder screen pin through the impeller and screen and insert the cotter pin
24
Realign the discharge chute on the impeller housing and insert the spacers
25
Insert the mounting bolt then thread and tighten the nut
26
"Fully position the chute, then thread and tighten the retaining knob screws"
27
Reinstall the chute assembly by sliding it onto the lower mounting bolt behind the washer and nut then align it on the upper bolts
28
Thread and tighten the bolts to secure the support to the base
29
Position the shredder screen mounting post in the hole in the inner flair housing then realign the outer housing
30
Rethread the two upper mounting screws using the speed clips
31
Slide the shredder screen pin through the impeller and screen and insert the cotter pin
32
"Insert the mounting bolt, then thread and tighten the nut"
33
Realign the shredder plate on the impeller housing bolts
34
Thread and tighten all eight mounting nuts to secure
Applicable Product Model
Parts Needed
Blade
$20.59
Total$0.00
Related Articles & Videos
09:46
Part Replacement
Cub Cadet Chipper Shredder Impeller Assembly Replacement (981-04094)
14:48
Part Replacement
Cub Cadet Chipper Shredder Inner Flail Housing Replacement (681050634021)
03:13
Part Replacement
Cub Cadet Chipper Shredder Upper Chute Hinge Replacement (981-04032)
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com