Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Microwave Oven Door Latch Replacement 5304519330 
Frigidaire Microwave Oven Door Latch Replacement 5304519330
Skill Level
Total Parts Cost
$25.14Estimated Savings
$112.5007:24
- Description
This video provides step-by-step repair instructions for replacing the door latch on a Frigidaire microwave oven (Model FPMO227NUFA). The most common reason for replacing this part is if the door will not close properly.
All of the information for this video is applicable to the following brands:
Frigidaire
All of the information for this video is applicable to the following brands:
Frigidaire
Step By Step Instructions
1
Frigidaire Microwave Oven - FPMO227NUFA
2
Frigidaire Microwave Oven Door Latch Replacement
3
Tools needed: T-15 tamper-proof Torx bit, Phillips-head screwdriver, small flat-head screwdriver, putty knife, needle-nose pliers.
4
Shock
5
Because of the high voltage and high current used by microwave ovens, be aware that repairing this appliance poses a substantial risk for injury or death if precautions are not taken.
6
You should always unplug the microwave before you attempt any disassembly.
7
Since high voltage capacitors used in microwaves may retain a charge even after the microwave has been unplugged, we recommend that only experienced professionals access and replace internal components.
8
Unthread the six rear screws securing the cover using the T-15 tamper-proof Torx bit.
9
Unthread the screw on the right side of the cover as well.
10
Sharp
11
Pull the rear sides of the cover out then lift the cover up and pull back to fully remove.
12
Shock
13
You should release the potentially stored electrical charge in the capacitor to avoid injury.
14
You can do this by placing needle-nose pliers with an insulated handle across each set of terminals.
15
Using the Phillips-head screwdriver, unthread the two screws securing the upper door hinge.
16
With the screws unthreaded, open the door and lift the door assembly off the lower hinge.
17
Set the door on its front on a towel or blanket.
18
Use the putty knife and the small flat-head screwdriver to release the retaining clips securing the inner panel trim.
19
You will need to work your way around the inside edge to fully detach the trim.
20
Next, use the putty knife and small flat-head screwdriver to release the retaining tabs on the outer door panel securing the inner panel.
21
Fully separate the inner door panel from the outer panel.
22
Use the needle-nose pliers to detach the door latch spring from the inner panel.
23
You can now slide the old door latch to the left to remove.
24
To prepare the new door latch for installation, transfer the spring from the old latch to the new one.
25
Insert the tabs into the slots in the inner panel, slide the latch to the right, then attach the opposite end of the spring to the tab on the inner panel.
26
Make sure the upper hinge is positioned on the inner panel, then align the panel in the outer panel and snap it into place.
27
Properly realign the trim and snap the trim into position.
28
Reinstall the door by aligning the bottom of the door on the lower hinge pin.
29
Align the upper hinge on the frame, then thread the two screws to secure the hinge.
30
Reinstall the microwave oven cover by first aligning the top edge then the sides.
31
Thread and tighten the seven screws to secure.
32
Plug the power cord back in and the microwave oven should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the door latch on a Frigidaire microwave oven (Model FPMO227NUFA). The most common reason for replacing this part is if the door will not close properly.
All of the information for this video is applicable to the following brands:
Frigidaire
All of the information for this video is applicable to the following brands:
Frigidaire
Step-By-Step Instructions
1
Frigidaire Microwave Oven - FPMO227NUFA
2
Frigidaire Microwave Oven Door Latch Replacement
3
Tools needed: T-15 tamper-proof Torx bit, Phillips-head screwdriver, small flat-head screwdriver, putty knife, needle-nose pliers.
4
Shock
5
Because of the high voltage and high current used by microwave ovens, be aware that repairing this appliance poses a substantial risk for injury or death if precautions are not taken.
6
You should always unplug the microwave before you attempt any disassembly.
7
Since high voltage capacitors used in microwaves may retain a charge even after the microwave has been unplugged, we recommend that only experienced professionals access and replace internal components.
8
Unthread the six rear screws securing the cover using the T-15 tamper-proof Torx bit.
9
Unthread the screw on the right side of the cover as well.
10
Sharp
11
Pull the rear sides of the cover out then lift the cover up and pull back to fully remove.
12
Shock
13
You should release the potentially stored electrical charge in the capacitor to avoid injury.
14
You can do this by placing needle-nose pliers with an insulated handle across each set of terminals.
15
Using the Phillips-head screwdriver, unthread the two screws securing the upper door hinge.
16
With the screws unthreaded, open the door and lift the door assembly off the lower hinge.
17
Set the door on its front on a towel or blanket.
18
Use the putty knife and the small flat-head screwdriver to release the retaining clips securing the inner panel trim.
19
You will need to work your way around the inside edge to fully detach the trim.
20
Next, use the putty knife and small flat-head screwdriver to release the retaining tabs on the outer door panel securing the inner panel.
21
Fully separate the inner door panel from the outer panel.
22
Use the needle-nose pliers to detach the door latch spring from the inner panel.
23
You can now slide the old door latch to the left to remove.
24
To prepare the new door latch for installation, transfer the spring from the old latch to the new one.
25
Insert the tabs into the slots in the inner panel, slide the latch to the right, then attach the opposite end of the spring to the tab on the inner panel.
26
Make sure the upper hinge is positioned on the inner panel, then align the panel in the outer panel and snap it into place.
27
Properly realign the trim and snap the trim into position.
28
Reinstall the door by aligning the bottom of the door on the lower hinge pin.
29
Align the upper hinge on the frame, then thread the two screws to secure the hinge.
30
Reinstall the microwave oven cover by first aligning the top edge then the sides.
31
Thread and tighten the seven screws to secure.
32
Plug the power cord back in and the microwave oven should be ready for use.
Applicable Product Model
Parts Needed
Door Hook
$25.14
Total$0.00
Related Articles & Videos
04:41
Part Replacement
Frigidaire Microwave Oven Control Panel Assembly Replacement 5304519365
05:18
Part Replacement
Frigidaire Microwave Oven Door Release Push Button Replacement 5304519323
06:46
Part Replacement
Frigidaire Microwave Oven Door Interlock Switch Replacement 5304515182
05:26
Part Replacement
Frigidaire Microwave Oven Door Release Push Button Spring Replacement 5304519324
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com