Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Range Vent Hood Lamp Holder Wire Harness Replacement 5304482315 
Frigidaire Range Vent Hood Lamp Holder Wire Harness Replacement 5304482315
Skill Level
Total Parts Cost
$172.34Estimated Savings
$112.5004:42
- Description
This video provides step-by-step repair instructions for replacing the lamp holder wire harness on a Frigidaire Range Vent Hood (model FHWC3660LSA). The most common reason for replacing this part is if the lights on the hood are not working.
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
Step By Step Instructions
1
Frigidaire Range Vent Hood - FHWC3660LSA
2
Frigidaire Range Vent Hood Lamp Holder Wire Harness Assembly Replacement
3
Tools needed: Phillips-head screwdriver, small flat-head screwdriver
4
Shock
5
Before you begin the procedure, be sure to turn off the power supply to the hood.
6
Pull the right-side lever down to release the grease filter.
7
Rotate both light bulbs counter-clockwise to release them from their respective holders.
8
Now rotate the two lamp holder assemblies to release them from the hood.
9
Use the Phillips-head screwdriver to unthread the four screws to release the terminal block cover.
10
Cut the two zip-ties securing the wire harness.
11
Note the orientation of the wires, then use the small flat-head screwdriver to loosen the screws to release the wires from the terminal blocks.
12
To install the new lamp holder wire harness assembly, insert the wires into the appropriate terminals in the terminal blocks and tighten the screws to secure.
13
Use new zip ties to bundle the wires together.
14
Reposition the terminal blocks in the housing then align the cover.
15
Thread the screws to secure the cover.
16
Align the two lamp holder assemblies with the holes in the hood and rotate both to lock them into position.
17
Insert the light bulb terminals into the holder and rotate clockwise to secure both bulbs.
18
Reinstall the grease filter by aligning the left side tabs with the slots in the hood, then pull the lever to align the right side.
19
Turn the power supply back on and the range vent hood should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the lamp holder wire harness on a Frigidaire Range Vent Hood (model FHWC3660LSA). The most common reason for replacing this part is if the lights on the hood are not working.
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
Step-By-Step Instructions
1
Frigidaire Range Vent Hood - FHWC3660LSA
2
Frigidaire Range Vent Hood Lamp Holder Wire Harness Assembly Replacement
3
Tools needed: Phillips-head screwdriver, small flat-head screwdriver
4
Shock
5
Before you begin the procedure, be sure to turn off the power supply to the hood.
6
Pull the right-side lever down to release the grease filter.
7
Rotate both light bulbs counter-clockwise to release them from their respective holders.
8
Now rotate the two lamp holder assemblies to release them from the hood.
9
Use the Phillips-head screwdriver to unthread the four screws to release the terminal block cover.
10
Cut the two zip-ties securing the wire harness.
11
Note the orientation of the wires, then use the small flat-head screwdriver to loosen the screws to release the wires from the terminal blocks.
12
To install the new lamp holder wire harness assembly, insert the wires into the appropriate terminals in the terminal blocks and tighten the screws to secure.
13
Use new zip ties to bundle the wires together.
14
Reposition the terminal blocks in the housing then align the cover.
15
Thread the screws to secure the cover.
16
Align the two lamp holder assemblies with the holes in the hood and rotate both to lock them into position.
17
Insert the light bulb terminals into the holder and rotate clockwise to secure both bulbs.
18
Reinstall the grease filter by aligning the left side tabs with the slots in the hood, then pull the lever to align the right side.
19
Turn the power supply back on and the range vent hood should be ready for use.
Applicable Product Model
Related Articles & Videos
05:29
Part Replacement
Frigidaire Range Vent Hood Recirculation Kit Installation 5304482271
04:51
Part Replacement
Frigidaire Range Vent Hood Selector Switch Assembly Replacement 5304482236
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com