Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Range Vent Hood Blower Cover Replacement 5304482238 
Frigidaire Range Vent Hood Blower Cover Replacement 5304482238
Skill Level
Total Parts Cost
$9.40Estimated Savings
$112.5016:27
- Description
This video provides step-by-step repair instructions for replacing the blower cover on a Frigidaire Range Vent Hood (model FHWC3660LSA). The most common reason for replacing this part is if it is damaged or missing.
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
Step By Step Instructions
1
Frigidaire Range Vent Hood - FHWC3660LSA
2
Frigidaire Range Vent Hood Blower Cover Replacement
3
Tools needed: Phillips-head screwdriver, 2.5mm Allen wrench, 7mm nut driver, small awl, needle-nose pliers
4
Shock
5
Before you begin, be sure to turn off the power supply to the hood.
6
Use the Phillips-head screwdriver to unthread the left and right side screws securing the upper chimney to the upper mounting bracket.
7
Heavy
8
Slide the chimney down into the lower chimney then have an assistant help to lift both sections up to detach them from the lower mounting bracket.
9
Detach the venting from the damper.
10
Unthread the two screws securing the junction box cover.
11
Remove the cover and note the orientation of the power and grounding wires.
12
Untwist the wire nuts to separate the power wires.
13
Use the 7mm nut driver to unthread the nut to release the grounding wire.
14
Pull the wires out of the junction box.
15
Unthread the four mounting screws securing the canopy glass using the 2.5mm allen wrench.
16
With the screws unthreaded, have an assistant help you to remove the glass.
17
Pull the right-side lever down to release the grease filter.
18
Sharp
19
Unthread the two lower mounting screws securing the appliance to the wall.
20
Next, loosen the two upper mounting screws.
21
Heavy
22
With the screws loosened, you can lift the vent hood up and out to remove.
23
With the front of the hood facing down, set it on a towel or blanket.
24
Now unthread the two rear outside screws securing the stainless-steel panel to the cabinet.
25
Next, unthread the two sets of nuts and bolts in the middle.
26
Now unthread the eight screws securing the panel to the base of the appliance.
27
Rotate the two light bulbs counter-clockwise to remove them from their holders.
28
Sharp
29
You can now detach the panel.
30
Unthread the screws to release the selector switch assembly so you can set the panel aside.
31
Now rotate the two lamp holder assemblies to release them from the cabinet.
32
Unthread the two left-side screws securing the blower assembly.
33
Unthread the two right-side screws as well.
34
Next, unthread the two screws securing the blower assembly bracket to the rear mounting plate.
35
Use the 7mm nut driver to unthread the nut to release the blower assembly grounding wire.
36
Maneuver the blower assembly out of the cabinet so you can reach the cover you?re replacing.
37
Now unthread the three screws securing the appropriate blower cover using the Phillips-head screwdriver.
38
Flip the cover over to access the tabs securing the grille, then use the needle-nose pliers to depress the tabs to detach the grille from the cover.
39
If you need to replace the blower cover with the motor attached, rotate the motor mounting bracket counter-clockwise to release the old cover.
40
To install the new blower cover, first insert the motor wires into the appropriate slot if applicable.
41
Align the cover on the motor mounting bracket then rotate the bracket clockwise to lock the cover into place.
42
You can use the small awl to help hold the cover in position.
43
Align the grille on the new cover and snap it into place.
44
Reposition the cover on the blower assembly and thread the three screws to secure.
45
Reseat the blower assembly in the cabinet.
46
Align the blower assembly grounding wire on the cabinet post, slide on the washer, then thread the nut to secure.
47
Fully position the blower assembly and thread the two screws to secure the assembly bracket to the rear mounting plate.
48
Thread the two left-side screws.
49
Thread the two right-side screws as well.
50
Align the two lamp holder assemblies with the holes in the cabinet and rotate both to lock them into place.
51
Realign the selector switch assembly in the stainless-steel panel and secure it with the screws.
52
Reposition the panel and rethread the eight inner mounting screws.
53
Thread the two sets of nuts and bolts in the middle to secure the panel to the cabinet.
54
Rethread the two outside screws as well.
55
Replace the two light bulbs by inserting the terminals into the holders then rotate clockwise.
56
Reinstall the range vent hood by aliging the rear slots over the upper mounting screws threaded into the wall.
57
Partially tighten the screws to maintain an even gap between the wall and cabinet.
58
Rethread the lower mounting screws.
59
Reinstall the grease filter by aligning the left side tabs with the slots in the hood, then pull the lever to align the right side.
60
Before you reinstall the canopy glass, confirm the hood gasket is intact and aligned.
61
Reposition the glass.
62
Thread the four screws to secure.
63
Fragile
64
Avoid over-tightening the screws.
65
Feed the power and grounding wires through the hole in the junction box.
66
Secure the grounding wires with the nut.
67
Join the black wires and use the wire nut to twist the wires together.
68
Do the same to join the white wires together.
69
Replace the junction box cover and secure it with the screws.
70
Attach the venting to the damper.
71
Slide the upper chimney section into the lower chimney section.
72
Now align the bottom edge of the lower chimney in the groove between the canopy glass and blower housing cabinet.
73
Hook the lower chimney slots on the lower mounting bracket tabs.
74
Lift the upper chimney section up so its flush with the ceiling, then thread the screws to secure the chimney to the upper mounting bracket.
75
Turn the power supply back on and the range vent hood should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the blower cover on a Frigidaire Range Vent Hood (model FHWC3660LSA). The most common reason for replacing this part is if it is damaged or missing.
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
Step-By-Step Instructions
1
Frigidaire Range Vent Hood - FHWC3660LSA
2
Frigidaire Range Vent Hood Blower Cover Replacement
3
Tools needed: Phillips-head screwdriver, 2.5mm Allen wrench, 7mm nut driver, small awl, needle-nose pliers
4
Shock
5
Before you begin, be sure to turn off the power supply to the hood.
6
Use the Phillips-head screwdriver to unthread the left and right side screws securing the upper chimney to the upper mounting bracket.
7
Heavy
8
Slide the chimney down into the lower chimney then have an assistant help to lift both sections up to detach them from the lower mounting bracket.
9
Detach the venting from the damper.
10
Unthread the two screws securing the junction box cover.
11
Remove the cover and note the orientation of the power and grounding wires.
12
Untwist the wire nuts to separate the power wires.
13
Use the 7mm nut driver to unthread the nut to release the grounding wire.
14
Pull the wires out of the junction box.
15
Unthread the four mounting screws securing the canopy glass using the 2.5mm allen wrench.
16
With the screws unthreaded, have an assistant help you to remove the glass.
17
Pull the right-side lever down to release the grease filter.
18
Sharp
19
Unthread the two lower mounting screws securing the appliance to the wall.
20
Next, loosen the two upper mounting screws.
21
Heavy
22
With the screws loosened, you can lift the vent hood up and out to remove.
23
With the front of the hood facing down, set it on a towel or blanket.
24
Now unthread the two rear outside screws securing the stainless-steel panel to the cabinet.
25
Next, unthread the two sets of nuts and bolts in the middle.
26
Now unthread the eight screws securing the panel to the base of the appliance.
27
Rotate the two light bulbs counter-clockwise to remove them from their holders.
28
Sharp
29
You can now detach the panel.
30
Unthread the screws to release the selector switch assembly so you can set the panel aside.
31
Now rotate the two lamp holder assemblies to release them from the cabinet.
32
Unthread the two left-side screws securing the blower assembly.
33
Unthread the two right-side screws as well.
34
Next, unthread the two screws securing the blower assembly bracket to the rear mounting plate.
35
Use the 7mm nut driver to unthread the nut to release the blower assembly grounding wire.
36
Maneuver the blower assembly out of the cabinet so you can reach the cover you?re replacing.
37
Now unthread the three screws securing the appropriate blower cover using the Phillips-head screwdriver.
38
Flip the cover over to access the tabs securing the grille, then use the needle-nose pliers to depress the tabs to detach the grille from the cover.
39
If you need to replace the blower cover with the motor attached, rotate the motor mounting bracket counter-clockwise to release the old cover.
40
To install the new blower cover, first insert the motor wires into the appropriate slot if applicable.
41
Align the cover on the motor mounting bracket then rotate the bracket clockwise to lock the cover into place.
42
You can use the small awl to help hold the cover in position.
43
Align the grille on the new cover and snap it into place.
44
Reposition the cover on the blower assembly and thread the three screws to secure.
45
Reseat the blower assembly in the cabinet.
46
Align the blower assembly grounding wire on the cabinet post, slide on the washer, then thread the nut to secure.
47
Fully position the blower assembly and thread the two screws to secure the assembly bracket to the rear mounting plate.
48
Thread the two left-side screws.
49
Thread the two right-side screws as well.
50
Align the two lamp holder assemblies with the holes in the cabinet and rotate both to lock them into place.
51
Realign the selector switch assembly in the stainless-steel panel and secure it with the screws.
52
Reposition the panel and rethread the eight inner mounting screws.
53
Thread the two sets of nuts and bolts in the middle to secure the panel to the cabinet.
54
Rethread the two outside screws as well.
55
Replace the two light bulbs by inserting the terminals into the holders then rotate clockwise.
56
Reinstall the range vent hood by aliging the rear slots over the upper mounting screws threaded into the wall.
57
Partially tighten the screws to maintain an even gap between the wall and cabinet.
58
Rethread the lower mounting screws.
59
Reinstall the grease filter by aligning the left side tabs with the slots in the hood, then pull the lever to align the right side.
60
Before you reinstall the canopy glass, confirm the hood gasket is intact and aligned.
61
Reposition the glass.
62
Thread the four screws to secure.
63
Fragile
64
Avoid over-tightening the screws.
65
Feed the power and grounding wires through the hole in the junction box.
66
Secure the grounding wires with the nut.
67
Join the black wires and use the wire nut to twist the wires together.
68
Do the same to join the white wires together.
69
Replace the junction box cover and secure it with the screws.
70
Attach the venting to the damper.
71
Slide the upper chimney section into the lower chimney section.
72
Now align the bottom edge of the lower chimney in the groove between the canopy glass and blower housing cabinet.
73
Hook the lower chimney slots on the lower mounting bracket tabs.
74
Lift the upper chimney section up so its flush with the ceiling, then thread the screws to secure the chimney to the upper mounting bracket.
75
Turn the power supply back on and the range vent hood should be ready for use.
Applicable Product Model
Related Articles & Videos
05:29
Part Replacement
Frigidaire Range Vent Hood Recirculation Kit Installation 5304482271
04:51
Part Replacement
Frigidaire Range Vent Hood Selector Switch Assembly Replacement 5304482236
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com