Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Induction Range Ferrite Coil Replacement 5304519440 
Frigidaire Induction Range Ferrite Coil Replacement 5304519440
Skill Level
Total Parts Cost
$26.89Estimated Savings
$112.5003:41
- Description
This video provides step-by-step repair instructions for replacing the ferrite coil on a Frigidaire induction range. The most common reason for replacing this part is if the range is not heating properly.
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
Step By Step Instructions
1
Frigidaire Induction Range - GCRI3058AFD
2
Frigidaire Induction Range Ferrite Coil Replacement
3
Tools needed: Phillips-head screwdriver, needle-nose pliers
4
Shock
5
Before you begin the procedure, unplug the power cord.
6
Open the oven door and use the Phillips-head screwdriver to unthread the three screws securing the main top.
7
Heavy
8
With the screws unthreaded, pull the main top forward to fully remove.
9
Next, unthread the three screws securing the induction coil support panel.
10
Now note the hole locations where the retaining clips for the appropriate rear induction coil are inserted into.
11
Sharp
12
Detach the induction coil covering the ferrite coil you?re replacing and move it out of the way.
13
Disconnect the two ferrite coil wires.
14
Lift up the support panel and use the needle-nose pliers to depress the tabs to release the ferrite coil retainer from the panel and set the old coil aside.
15
To install the new ferrite coil, snap the coil retainer into the support panel, then connect the two wires to the respective module wire and grounding terminal.
16
Reposition the induction coil and snap the retaining clips into the correct holes in the support bracket.
17
Realign the induction coil support panel as necessary and rethread the three mounting screws.
18
Reinstall the main top by aligning the sides under the front support bracket, then carefully slide the top back, pressing the induction coils down as you do this.
19
With the top in place, thread the three screws in front to fully secure it.
20
Plug the power cord back in and the induction range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the ferrite coil on a Frigidaire induction range. The most common reason for replacing this part is if the range is not heating properly.
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
Step-By-Step Instructions
1
Frigidaire Induction Range - GCRI3058AFD
2
Frigidaire Induction Range Ferrite Coil Replacement
3
Tools needed: Phillips-head screwdriver, needle-nose pliers
4
Shock
5
Before you begin the procedure, unplug the power cord.
6
Open the oven door and use the Phillips-head screwdriver to unthread the three screws securing the main top.
7
Heavy
8
With the screws unthreaded, pull the main top forward to fully remove.
9
Next, unthread the three screws securing the induction coil support panel.
10
Now note the hole locations where the retaining clips for the appropriate rear induction coil are inserted into.
11
Sharp
12
Detach the induction coil covering the ferrite coil you?re replacing and move it out of the way.
13
Disconnect the two ferrite coil wires.
14
Lift up the support panel and use the needle-nose pliers to depress the tabs to release the ferrite coil retainer from the panel and set the old coil aside.
15
To install the new ferrite coil, snap the coil retainer into the support panel, then connect the two wires to the respective module wire and grounding terminal.
16
Reposition the induction coil and snap the retaining clips into the correct holes in the support bracket.
17
Realign the induction coil support panel as necessary and rethread the three mounting screws.
18
Reinstall the main top by aligning the sides under the front support bracket, then carefully slide the top back, pressing the induction coils down as you do this.
19
With the top in place, thread the three screws in front to fully secure it.
20
Plug the power cord back in and the induction range should be ready for use.
Applicable Product Model
Related Articles & Videos
10:14
Part Replacement
Frigidaire Induction Range Induction Wire Harness Replacement 5304519440
04:05
Part Replacement
Frigidaire Range Communication Wire Harness Replacement 5304522699
06:43
Part Replacement
Frigidaire Induction Range Low-Voltage Wire Harness Replacement 5304522701
04:31
Part Replacement
Frigidaire Induction Range Oven Door Hinge Replacement 5304522696
06:12
Part Replacement
Frigidaire Induction Range Induction Module Replacement 5304527384
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com