Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Range Communication Wire Harness Replacement 5304522699 
Frigidaire Range Communication Wire Harness Replacement 5304522699
Skill Level
Total Parts Cost
$22.89Estimated Savings
$112.5004:05
- Description
This video provides step-by-step repair instructions for replacing the communication wire harness on a Frigidaire range. The most common reason for replacing this part is if the range is not heating properly.
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
Step By Step Instructions
1
Frigidaire Induction Range - GCRI3058AFD
2
Frigidaire Induction Range Communication Wire Harness Replacement
3
Tools needed: quarter-inch nut driver
4
Shock
5
Before you begin the procedure, unplug the power cord.
6
Heavy
7
Have an assistant help you to move the range away from the wall.
8
Use the quarter-inch nut driver to unthread the six screws securing the upper rear access panel.
9
Sharp
10
Set the panel aside.
11
Next, unthread the lower screw securing the power cord retaining plate.
12
Now unthread the five mounting screws securing the range?s lower rear access panel.
13
Sharp
14
With the screws unthreaded, detach the panel and set it aside.
15
Disconnect the communication wire connecter from both the control board and the oven relay board and you can fully remove the old harness.
16
To install the new communication wire harness, connect one connecter to the control board, then feed the wires through the three retaining wires and connect the opposite connecter to the oven relay board.
17
Reinstall the lower rear access panel by first inserting the power cord retaining plate, then align the notches on the bottom of the access panel with the tabs and thread the five screws to secure.
18
Rethread the lower screw to secure the power cord retaining plate to the access panel.
19
Reinstall the upper rear access panel by sliding the tabs under the control panel, then thread the center screw first to hold it in place.
20
Replace the five additional screws to fully secure.
21
Move the appliance back against the wall.
22
Plug the power cord back in and the induction range should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the communication wire harness on a Frigidaire range. The most common reason for replacing this part is if the range is not heating properly.
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
All of the information for this part replacement video is applicable to the following brands:
Frigidaire
Step-By-Step Instructions
1
Frigidaire Induction Range - GCRI3058AFD
2
Frigidaire Induction Range Communication Wire Harness Replacement
3
Tools needed: quarter-inch nut driver
4
Shock
5
Before you begin the procedure, unplug the power cord.
6
Heavy
7
Have an assistant help you to move the range away from the wall.
8
Use the quarter-inch nut driver to unthread the six screws securing the upper rear access panel.
9
Sharp
10
Set the panel aside.
11
Next, unthread the lower screw securing the power cord retaining plate.
12
Now unthread the five mounting screws securing the range?s lower rear access panel.
13
Sharp
14
With the screws unthreaded, detach the panel and set it aside.
15
Disconnect the communication wire connecter from both the control board and the oven relay board and you can fully remove the old harness.
16
To install the new communication wire harness, connect one connecter to the control board, then feed the wires through the three retaining wires and connect the opposite connecter to the oven relay board.
17
Reinstall the lower rear access panel by first inserting the power cord retaining plate, then align the notches on the bottom of the access panel with the tabs and thread the five screws to secure.
18
Rethread the lower screw to secure the power cord retaining plate to the access panel.
19
Reinstall the upper rear access panel by sliding the tabs under the control panel, then thread the center screw first to hold it in place.
20
Replace the five additional screws to fully secure.
21
Move the appliance back against the wall.
22
Plug the power cord back in and the induction range should be ready for use.
Applicable Product Model
Related Articles & Videos
06:43
Part Replacement
Frigidaire Induction Range Low-Voltage Wire Harness Replacement 5304522701
04:31
Part Replacement
Frigidaire Induction Range Oven Door Hinge Replacement 5304522696
06:12
Part Replacement
Frigidaire Induction Range Induction Module Replacement 5304527384
06:09
Part Replacement
Frigidaire Induction Range Convection Fan Motor Replacement 316256100
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com