Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Refrigerator Freezer Evaporator Fan Blade #ADP36665705
LG Refrigerator Freezer Evaporator Fan Blade #ADP36665705
Skill Level
Total Parts Cost
$25.95Estimated Savings
$112.5006:52
- Description
This video provides step-by-step repair instructions for replacing the freezer evaporator fan blade in an LG Refrigerator (Model LFCS22520S).
All of the information for this freezer evaporator fan blade replacement video is applicable to the following brands:
LG
Tools needed: Phillips Screwdriver/Drill Driver, Flathead Screwdriver
All of the information for this freezer evaporator fan blade replacement video is applicable to the following brands:
LG
Tools needed: Phillips Screwdriver/Drill Driver, Flathead Screwdriver
Step By Step Instructions
1
To replace the evaporator fan blade in this LG refrigerator, you will need a flathead screwdriver and a Phillips screwdriver or drill driver with a number two Phillips bit.
2
Be sure to unplug the appliance before working with any electrical components.
3
Fully extend out the top freezer tray by lifting the front, then pull out the ice container.
4
Next, pull and lift out the freezer tray.
5
Lift the bottom freezer drawer out from the rear.
6
Use the jeweler's screwdriver to depress the tab on the drawer gear and pull up to detach it from the slide rail.
7
Pull the bar away from the other gear.
8
Loosen and remove the two Phillips screws securing the freezer door and lift it up and out to remove it.
9
Remove the two screws on the ice maker.
10
Use the flathead screwdriver to release the tabs and pull it down, sliding it forward at the same time.
11
Unplug the wire harness and remove the ice maker.
12
Unsnap the evaporator cover.
13
Unplug the temperature sensor and the evaporator fan.
14
Pull off the evaporator fan blade.
15
To install the new fan blade, press the blade onto the shaft of the motor.
16
Plug in the evaporator and temperature sensor.
17
Position and snap the evaporator cover into place.
18
Plug in the wire harness for the ice maker.
19
Slide the back of the ice maker into place and push up to snap in the tabs.
20
Thread and tighten the two screws to secure the ice maker.
21
Set the freezer door by hooking the connector rails to the sliders.
22
Screw in the two Phillips head screws to secure the door.
23
Insert the bar into the set gear and snap the gear on the other end into its slot within the slide rail.
24
This can be difficult to align.
25
Place the drawer back inside the freezer.
26
Slide the tray back into the guide rails, then insert the ice container.
27
Plug in the appliance.
28
The LG refrigerator should now be ready for use.
Description
This video provides step-by-step repair instructions for replacing the freezer evaporator fan blade in an LG Refrigerator (Model LFCS22520S).
All of the information for this freezer evaporator fan blade replacement video is applicable to the following brands:
LG
Tools needed: Phillips Screwdriver/Drill Driver, Flathead Screwdriver
All of the information for this freezer evaporator fan blade replacement video is applicable to the following brands:
LG
Tools needed: Phillips Screwdriver/Drill Driver, Flathead Screwdriver
Step-By-Step Instructions
1
To replace the evaporator fan blade in this LG refrigerator, you will need a flathead screwdriver and a Phillips screwdriver or drill driver with a number two Phillips bit.
2
Be sure to unplug the appliance before working with any electrical components.
3
Fully extend out the top freezer tray by lifting the front, then pull out the ice container.
4
Next, pull and lift out the freezer tray.
5
Lift the bottom freezer drawer out from the rear.
6
Use the jeweler's screwdriver to depress the tab on the drawer gear and pull up to detach it from the slide rail.
7
Pull the bar away from the other gear.
8
Loosen and remove the two Phillips screws securing the freezer door and lift it up and out to remove it.
9
Remove the two screws on the ice maker.
10
Use the flathead screwdriver to release the tabs and pull it down, sliding it forward at the same time.
11
Unplug the wire harness and remove the ice maker.
12
Unsnap the evaporator cover.
13
Unplug the temperature sensor and the evaporator fan.
14
Pull off the evaporator fan blade.
15
To install the new fan blade, press the blade onto the shaft of the motor.
16
Plug in the evaporator and temperature sensor.
17
Position and snap the evaporator cover into place.
18
Plug in the wire harness for the ice maker.
19
Slide the back of the ice maker into place and push up to snap in the tabs.
20
Thread and tighten the two screws to secure the ice maker.
21
Set the freezer door by hooking the connector rails to the sliders.
22
Screw in the two Phillips head screws to secure the door.
23
Insert the bar into the set gear and snap the gear on the other end into its slot within the slide rail.
24
This can be difficult to align.
25
Place the drawer back inside the freezer.
26
Slide the tray back into the guide rails, then insert the ice container.
27
Plug in the appliance.
28
The LG refrigerator should now be ready for use.
Applicable Product Model
Parts Needed
Condenser Fan Blade
$25.95
Total$0.00
Related Articles & Videos
08:35
Part Replacement
LG Refrigerator Front Freezer Evaporator Motor Support #5040JA2009B
08:15
Part Replacement
LG Refrigerator Rear Freezer Evaporator Motor Support #5040JA2004A
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com