Video & Articles: Appliance & Equipment RepairLG Refrigerator Freezer Fan Motor #EAU63103209

LG Refrigerator Freezer Fan Motor #EAU63103209

11:04
This video provides step-by-step repair instructions for replacing the freezer fan motor in an LG Refrigerator (Model LFCS22520S).

All of the information for this freezer fan motor replacement video is applicable to the following brands:
LG

Tools needed: Phillips Screwdriver/Drill Driver, Zip Ties, Utility Knife, Flathead Screwdriver

Step By Step Instructions

1
To replace the freezer fan motor in this lg refrigerator…
2
You will need zip ties, a utility knife, a flathead screwdriver and a phillips screwdriver or drill driver with a number 2 phiillips bit.
3
Be sure to unplug the appliance before working with any electrical components.
4
Fully extend out the top freezer tray by lifting the front. then pull out the ice container.
5
Next, pull and lift out the freezer tray.
6
Lift the bottom freezer drawer out from the back.
7
Use the screwdriver to depress the tab on the drawer gear and pull up to detatch the bar from the slide rail.
8
Loosen and remove the two phillips screws securing the freezer door and lift it up and out to remove it.
9
Remove the two screws on the ice maker
10
Use the flathead screwdriver to release the tabs and pull it down, sliding it forward at the same time.
11
Unplug the wire harness and remove the ice maker.
12
Unsnap the evaporator cover
13
Unplug the temperature sensor and the evaporator fan.
14
Pull off the evaporator fan blade.
15
Unscrew the two phillips head screws on the support bracket and remove the bracket.
16
Cut the zip ties around the collected wires and remove the freezer fan motor, placing the rear motor support to the side.
17
To install the new fan motor…
18
Place the rear support and set in the fan motor.
19
Collect the wires and zip tie them to the freezer shroud, leave at least 12 inches of slack to plug in the motor .
20
Slide the bracket over the motor shaft then thread and tighten the two screws to secure it.
21
Press the fan blade onto the shaft of the motor.
22
Plug in the evaporator and temperature sensor
23
Position and snap the evaporator cover into place.
24
Plug in the wire harness for the ice maker.
25
Slide the back of the ice maker into place and push up to snap in the tabs.
26
Thread and tighten the two screws to secure the ice maker.
27
Set the freezer door by hooking the connector rails to the sliders.
28
Screw in the two phillips head screws to secure the door.
29
Insert the bar into the set gear and snap the gear on the other end into its slot within the slide rail. this can be difficult to align.
30
Place the drawer back inside the freezer.
31
Slide the tray back into the guide rails.
32
Then insert the ice container.
33
Plug in the appliance.
34
…. and the lg refrigerator should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the freezer fan motor in an LG Refrigerator (Model LFCS22520S).

All of the information for this freezer fan motor replacement video is applicable to the following brands:
LG

Tools needed: Phillips Screwdriver/Drill Driver, Zip Ties, Utility Knife, Flathead Screwdriver
Step-By-Step Instructions
1
To replace the freezer fan motor in this lg refrigerator…
2
You will need zip ties, a utility knife, a flathead screwdriver and a phillips screwdriver or drill driver with a number 2 phiillips bit.
3
Be sure to unplug the appliance before working with any electrical components.
4
Fully extend out the top freezer tray by lifting the front. then pull out the ice container.
5
Next, pull and lift out the freezer tray.
6
Lift the bottom freezer drawer out from the back.
7
Use the screwdriver to depress the tab on the drawer gear and pull up to detatch the bar from the slide rail.
8
Loosen and remove the two phillips screws securing the freezer door and lift it up and out to remove it.
9
Remove the two screws on the ice maker
10
Use the flathead screwdriver to release the tabs and pull it down, sliding it forward at the same time.
11
Unplug the wire harness and remove the ice maker.
12
Unsnap the evaporator cover
13
Unplug the temperature sensor and the evaporator fan.
14
Pull off the evaporator fan blade.
15
Unscrew the two phillips head screws on the support bracket and remove the bracket.
16
Cut the zip ties around the collected wires and remove the freezer fan motor, placing the rear motor support to the side.
17
To install the new fan motor…
18
Place the rear support and set in the fan motor.
19
Collect the wires and zip tie them to the freezer shroud, leave at least 12 inches of slack to plug in the motor .
20
Slide the bracket over the motor shaft then thread and tighten the two screws to secure it.
21
Press the fan blade onto the shaft of the motor.
22
Plug in the evaporator and temperature sensor
23
Position and snap the evaporator cover into place.
24
Plug in the wire harness for the ice maker.
25
Slide the back of the ice maker into place and push up to snap in the tabs.
26
Thread and tighten the two screws to secure the ice maker.
27
Set the freezer door by hooking the connector rails to the sliders.
28
Screw in the two phillips head screws to secure the door.
29
Insert the bar into the set gear and snap the gear on the other end into its slot within the slide rail. this can be difficult to align.
30
Place the drawer back inside the freezer.
31
Slide the tray back into the guide rails.
32
Then insert the ice container.
33
Plug in the appliance.
34
…. and the lg refrigerator should be ready for use.

Applicable Product Model

Parts Needed
Total$0.00

Related Articles & Videos

06:52
Part Replacement
LG Refrigerator Freezer Evaporator Fan Blade #ADP36665705
08:35
Part Replacement
LG Refrigerator Front Freezer Evaporator Motor Support #5040JA2009B
08:15
Part Replacement
LG Refrigerator Rear Freezer Evaporator Motor Support #5040JA2004A
04:57
Part Replacement
LG Refrigerator Ice Maker Replacement AEQ72909603
07:52
Part Replacement
LG Refrigerator Condenser Fan Motor Replacement #EAU63103202