Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairCarrier/Gree ETAC Heat Pump Indoor Blower Wheel Replacement 10351004 
Carrier/Gree ETAC Heat Pump Indoor Blower Wheel Replacement 10351004
Skill Level
Total Parts Cost
$200.18Estimated Savings
$112.5006:39
- Description
This video provides step-by-step instructions for replacing the indoor blower wheel on a Carrier/Gree ETAC Heat Pump Unit. The most common reason for replacing this part is if it is damaged or noisy.
All of the information in this video is applicable to the following brands: Carrier, Gree
All of the information in this video is applicable to the following brands: Carrier, Gree
Step By Step Instructions
1
To replace the indoor blower wheel in this carrier/gree etac heat pump unit…
2
… you will need a #2 phillips-head screwdriver and a power drill with a 5/16th inch socket.
3
Before you begin, be sure to turn the unit off…
4
…and disconnect the power supply.
5
When performing this procedure, you will need to fully uninstall the unit from the wall.
6
To do this…
7
… remove the unit’s front panel by pulling the bottom of the panel out to release it from the tabs…then lift up.
8
If applicable, disconnect the wall thermostat wire connecter and the energy management wire connecter.
9
Using the power drill with the 5/16th inch socket, unthread the four mounting screws securing the unit to the wall sleeve.
10
Now have an assistant help you to slide the unit out of the sleeve…
11
… and set it on a towel or blanket.
12
Next, unthread the six screws securing the discharge air screen.
13
Set the screen aside.
14
Insert the #2 phillips-head screwdriver into the slot in the blower wheel to loosen the blower wheel set screw.
15
Next, unthread the three screws to release the left-side mounting bracket.
16
Now unthread the screw securing the blower wheel side access cover.
17
Lift the cover up and out.
18
Unthread the three screws to release the bearing cover.
19
With the cover detached, you can pull out the old blower wheel.
20
Before you attempt to install the new indoor blower wheel…
21
… confirm the set screw is loose.
22
Now insert the blower wheel through the indoor blower housing and onto the motor shaft, making sure the flat portion of the shaft aligns with the set screw.
23
Realign the bearing cover and thread the screws to secure.
24
Reposition the side access cover…
25
… and secure it with the screw.
26
Reposition the mounting bracket and thread the screws.
27
Center the new blower wheel in the housing, then tighten the set screw.
28
Reposition the discharge air screen and rethread the six screws to secure.
29
Reinstall the unit by sliding it into the wall sleeve until the seal rests against the front of the sleeve.
30
Rethread the mounting screws to secure the unit.
31
Avoid over-tightening the screws.
32
Reconnect the wall thermostat and energy management wire connecters if applicable.
33
Reinstall the front panel by aligning the tabs over the top rail then push the bottom of the panel in until it snaps into place.
34
Restore power to the unit…
35
… and the etac heat pump system should be ready for use.
Description
This video provides step-by-step instructions for replacing the indoor blower wheel on a Carrier/Gree ETAC Heat Pump Unit. The most common reason for replacing this part is if it is damaged or noisy.
All of the information in this video is applicable to the following brands: Carrier, Gree
All of the information in this video is applicable to the following brands: Carrier, Gree
Step-By-Step Instructions
1
To replace the indoor blower wheel in this carrier/gree etac heat pump unit…
2
… you will need a #2 phillips-head screwdriver and a power drill with a 5/16th inch socket.
3
Before you begin, be sure to turn the unit off…
4
…and disconnect the power supply.
5
When performing this procedure, you will need to fully uninstall the unit from the wall.
6
To do this…
7
… remove the unit’s front panel by pulling the bottom of the panel out to release it from the tabs…then lift up.
8
If applicable, disconnect the wall thermostat wire connecter and the energy management wire connecter.
9
Using the power drill with the 5/16th inch socket, unthread the four mounting screws securing the unit to the wall sleeve.
10
Now have an assistant help you to slide the unit out of the sleeve…
11
… and set it on a towel or blanket.
12
Next, unthread the six screws securing the discharge air screen.
13
Set the screen aside.
14
Insert the #2 phillips-head screwdriver into the slot in the blower wheel to loosen the blower wheel set screw.
15
Next, unthread the three screws to release the left-side mounting bracket.
16
Now unthread the screw securing the blower wheel side access cover.
17
Lift the cover up and out.
18
Unthread the three screws to release the bearing cover.
19
With the cover detached, you can pull out the old blower wheel.
20
Before you attempt to install the new indoor blower wheel…
21
… confirm the set screw is loose.
22
Now insert the blower wheel through the indoor blower housing and onto the motor shaft, making sure the flat portion of the shaft aligns with the set screw.
23
Realign the bearing cover and thread the screws to secure.
24
Reposition the side access cover…
25
… and secure it with the screw.
26
Reposition the mounting bracket and thread the screws.
27
Center the new blower wheel in the housing, then tighten the set screw.
28
Reposition the discharge air screen and rethread the six screws to secure.
29
Reinstall the unit by sliding it into the wall sleeve until the seal rests against the front of the sleeve.
30
Rethread the mounting screws to secure the unit.
31
Avoid over-tightening the screws.
32
Reconnect the wall thermostat and energy management wire connecters if applicable.
33
Reinstall the front panel by aligning the tabs over the top rail then push the bottom of the panel in until it snaps into place.
34
Restore power to the unit…
35
… and the etac heat pump system should be ready for use.
Applicable Product Model
Parts Needed
Blower Wheel
$200.18
Total$0.00
Related Articles & Videos
08:46
Part Replacement
Carrier/Gree ETAC Heat Pump Ambient Temperature Sensor Replacement 3900012123
10:01
Part Replacement
Carrier/Gree ETAC Heat Pump Outdoor Coil Temperature Sensor Replacement 390000372
08:31
Part Replacement
Carrier/Gree ETAC Heat Pump Indoor Coil Temperature Sensor Replacement 390000596
12:27
Part Replacement
Carrier/Gree ETAC Heat Pump Indoor Fan Motor Replacement 1501180211
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com