Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairCarrier/Gree ETAC Heat Pump Display Board Replacement 30562073 
Carrier/Gree ETAC Heat Pump Display Board Replacement 30562073
Skill Level
Total Parts Cost
$33.75Estimated Savings
$112.5005:21
- Description
This video provides step-by-step instructions for replacing the display board on a Carrier/Gree ETAC Heat Pump Unit. The most common reason for replacing this part is if the unit's display is malfunctioning.
All of the information in this video is applicable to the following brands: Carrier, Gree
All of the information in this video is applicable to the following brands: Carrier, Gree
Step By Step Instructions
1
To replace the display board in this carrier/gree etac heat pump unit…
2
… you will need a #2 phillips-head screwdriver, a pair of wire cutters, and zip-ties.
3
Before you begin the procedure, be sure to turn the unit off…
4
…and disconnect the power supply.
5
Remove the unit’s front panel by pulling the bottom of the panel out to release it from the tabs…then lift up.
6
Use the #2 phillips-head screwdriver to unthread the screw securing the control panel.
7
Detach the control panel.
8
Next, unthread the four screws to release the wire harness access panel.
9
Use the wire cutters to cut the zip-tie securing the wiring to the panel…
10
… as well as the zip-tie bundling the wires together.
11
Now release the two wire connecter locks so you can disconnect both wire connecters.
12
You can now unthread the four screws securing the old display board to the control panel.
13
To install the new display board…
14
… align it on the back side of the control panel…
15
… and thread the four screws to secure.
16
Reinstall the control panel by reconnecting the two wire connecters then slide the locks into place to secure.
17
Use new zip-ties to bundle the wires together…
18
… and to secure the wires to the access panel.
19
Reposition the access panel…
20
… and rethread the screws.
21
Realign the control panel and thread the screw to secure.
22
Reinstall the front panel by aligning the tabs over the top rail then push the bottom of the panel in until it snaps into place.
23
Restore power to the unit…
24
… and the etac heat pump system should be ready for use.
Description
This video provides step-by-step instructions for replacing the display board on a Carrier/Gree ETAC Heat Pump Unit. The most common reason for replacing this part is if the unit's display is malfunctioning.
All of the information in this video is applicable to the following brands: Carrier, Gree
All of the information in this video is applicable to the following brands: Carrier, Gree
Step-By-Step Instructions
1
To replace the display board in this carrier/gree etac heat pump unit…
2
… you will need a #2 phillips-head screwdriver, a pair of wire cutters, and zip-ties.
3
Before you begin the procedure, be sure to turn the unit off…
4
…and disconnect the power supply.
5
Remove the unit’s front panel by pulling the bottom of the panel out to release it from the tabs…then lift up.
6
Use the #2 phillips-head screwdriver to unthread the screw securing the control panel.
7
Detach the control panel.
8
Next, unthread the four screws to release the wire harness access panel.
9
Use the wire cutters to cut the zip-tie securing the wiring to the panel…
10
… as well as the zip-tie bundling the wires together.
11
Now release the two wire connecter locks so you can disconnect both wire connecters.
12
You can now unthread the four screws securing the old display board to the control panel.
13
To install the new display board…
14
… align it on the back side of the control panel…
15
… and thread the four screws to secure.
16
Reinstall the control panel by reconnecting the two wire connecters then slide the locks into place to secure.
17
Use new zip-ties to bundle the wires together…
18
… and to secure the wires to the access panel.
19
Reposition the access panel…
20
… and rethread the screws.
21
Realign the control panel and thread the screw to secure.
22
Reinstall the front panel by aligning the tabs over the top rail then push the bottom of the panel in until it snaps into place.
23
Restore power to the unit…
24
… and the etac heat pump system should be ready for use.
Applicable Product Model
Related Articles & Videos
08:46
Part Replacement
Carrier/Gree ETAC Heat Pump Ambient Temperature Sensor Replacement 3900012123
10:01
Part Replacement
Carrier/Gree ETAC Heat Pump Outdoor Coil Temperature Sensor Replacement 390000372
08:31
Part Replacement
Carrier/Gree ETAC Heat Pump Indoor Coil Temperature Sensor Replacement 390000596
12:27
Part Replacement
Carrier/Gree ETAC Heat Pump Indoor Fan Motor Replacement 1501180211
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com