Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Electric Dryer Drum Roller Assembly Replacement 4581EL2002H 
LG Electric Dryer Drum Roller Assembly Replacement 4581EL2002H
Skill Level
Total Parts Cost
$139.69Estimated Savings
$112.5008:36
- Description
This video provides step-by-step repair instructions for replacing the drum roller assembly on an LG electric dryer (model DLEX4000B). The most common reason for replacing this part is if the drum will not spin properly.
This coil replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This coil replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the drum roller assembly in your lg dryer…
2
You will need a phillips screwdriver or drill driver with a phillips bit, needlenose pliers, ratchet, 3/8 socket adapter, a 14mm socket and a 6mm socket.
3
Before you attempt this, be sure to turn off the power to the appliance…
4
Pull the dryer away from the wall.
5
Unthread the five screws to remove the bracket.
6
Slide the lid and lift it off to remove from the dryer.
7
Unthread the two screws holding the control panel.
8
Pry the three tabs then pull back and lift up to free the control panel.
9
Unplug the wire harness from the display board.
10
Unplug the led light.
11
Unplug the door switch.
12
Use needlenose pliers to remove the routing clip from the bulkhead.
13
Next unthread the two screws on the
14
Lower half of the panel.
15
Unthread the three screws on the top half of the dryer panel.
16
Be sure to support the panelwhile unthreading the three screws that secure the top of dryer panel.
17
Now lift and remove the front panel…
18
Remove the two screws holding the cross brace.
19
Unplug the moisture sensor harness.
20
Remove the four screws holding the bulkhead.
21
Lift the bulkhead up and out of its slots…
22
…and set it on a flat surface.
23
Use the ratchet to hold the roller shaft while loosening the nut.
24
To install the new drum roller assembly…
25
Set the washer on the shaft and insert it through the bulkhead assembly.
26
Thread and tighten the nut on the other side.
27
Insert the bulkhead into its slots…
28
… and rethread the four screws to secure it.
29
Plug in the moisture sensor.
30
Now reinstall the cross brace and rethread the two screws.
31
Insert the panel in the two slots at the bottom of the appliance.
32
Now rethread the three screws on the top half of the panel.
33
Rethread the two screws on the bottom half of the panel.
34
Plug in the led light.
35
Plug in the door switch.
36
Re-insert the routing clip
37
Plug the harness back into the display assembly.
38
Insert the control panel into its grooves and push forward to snap in place…
39
…then rethread the two screws that hold it in place.
40
Place the lid on the dryer and push forward to secure.
41
Rethread the five screws to reinstall the bracket.
42
Push the dryer back into place.
43
Turn the power supply back on…
44
…and your dryer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the drum roller assembly on an LG electric dryer (model DLEX4000B). The most common reason for replacing this part is if the drum will not spin properly.
This coil replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This coil replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the drum roller assembly in your lg dryer…
2
You will need a phillips screwdriver or drill driver with a phillips bit, needlenose pliers, ratchet, 3/8 socket adapter, a 14mm socket and a 6mm socket.
3
Before you attempt this, be sure to turn off the power to the appliance…
4
Pull the dryer away from the wall.
5
Unthread the five screws to remove the bracket.
6
Slide the lid and lift it off to remove from the dryer.
7
Unthread the two screws holding the control panel.
8
Pry the three tabs then pull back and lift up to free the control panel.
9
Unplug the wire harness from the display board.
10
Unplug the led light.
11
Unplug the door switch.
12
Use needlenose pliers to remove the routing clip from the bulkhead.
13
Next unthread the two screws on the
14
Lower half of the panel.
15
Unthread the three screws on the top half of the dryer panel.
16
Be sure to support the panelwhile unthreading the three screws that secure the top of dryer panel.
17
Now lift and remove the front panel…
18
Remove the two screws holding the cross brace.
19
Unplug the moisture sensor harness.
20
Remove the four screws holding the bulkhead.
21
Lift the bulkhead up and out of its slots…
22
…and set it on a flat surface.
23
Use the ratchet to hold the roller shaft while loosening the nut.
24
To install the new drum roller assembly…
25
Set the washer on the shaft and insert it through the bulkhead assembly.
26
Thread and tighten the nut on the other side.
27
Insert the bulkhead into its slots…
28
… and rethread the four screws to secure it.
29
Plug in the moisture sensor.
30
Now reinstall the cross brace and rethread the two screws.
31
Insert the panel in the two slots at the bottom of the appliance.
32
Now rethread the three screws on the top half of the panel.
33
Rethread the two screws on the bottom half of the panel.
34
Plug in the led light.
35
Plug in the door switch.
36
Re-insert the routing clip
37
Plug the harness back into the display assembly.
38
Insert the control panel into its grooves and push forward to snap in place…
39
…then rethread the two screws that hold it in place.
40
Place the lid on the dryer and push forward to secure.
41
Rethread the five screws to reinstall the bracket.
42
Push the dryer back into place.
43
Turn the power supply back on…
44
…and your dryer should be ready for use.
Applicable Product Model
Parts Needed
Drum Support Roller & Axle
$139.69
Total$0.00
Related Articles & Videos
14:49
Part Replacement
LG Electric Dryer Rear Drum Roller Assembly Replacement 4581EL2002H
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com