Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Electric Dryer Moisture Sensor Wire Harness Replacement 6631EL3003B 
LG Electric Dryer Moisture Sensor Wire Harness Replacement 6631EL3003B
Skill Level
Total Parts Cost
$30.75Estimated Savings
$112.5007:01
- Description
This video provides step-by-step repair instructions for replacing the moisture sensor wire harness on an LG electric dryer (model DLEX4000B). The most common reason for replacing this part is if the clothes are not drying properly.
This coil replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This coil replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the moisture sensor wire harness in your LG dryer, you will need a Phillips screwdriver or drill driver with a Phillips bit and needle-nose pliers.
2
Before you attempt this, be sure to turn off the power to the appliance.
3
Unthread the three screws securing the filter cover and remove it.
4
Pull the dryer away from the wall.
5
Unthread the five screws to remove the bracket.
6
Slide the lid and lift it off to remove from the dryer.
7
Unthread the two screws holding the control panel.
8
Pry the three tabs, then pull back and lift up to free the control panel.
9
Unplug the wire harness from the display PCB assembly.
10
Unplug the door switch.
11
Unthread the two screws on the lower half of the panel.
12
Unthread the three screws on the top half of the dryer panel.
13
Be sure to support the panel while unthreading the three screws that secure the top of the dryer panel.
14
Now lift and remove the front panel.
15
Now unplug the moisture sensor bracket, unplug the harness, and remove the routing clip.
16
To install the new moisture sensor wire harness, feed the wire through the dryer, insert the routing clip, plug in the harness, and plug in the moisture sensors.
17
Insert the panel in the two slots at the bottom of the appliance.
18
Now re-thread the three screws on the top half of the panel, re-thread the two screws on the bottom half of the panel, plug in the door switch, plug the wire harness back into the PCB assembly, insert the control panel into its grooves, and push forw
19
Then re-thread the two screws that hold it in place.
20
Place the lid on the dryer and push forward to secure.
21
Re-thread the five screws to reinstall the bracket.
22
Push the dryer back into place.
23
Next, align and slide the assembly into place within the dryer.
24
Re-thread the three screws to secure.
25
Turn the power supply back on, and your dryer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the moisture sensor wire harness on an LG electric dryer (model DLEX4000B). The most common reason for replacing this part is if the clothes are not drying properly.
This coil replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This coil replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the moisture sensor wire harness in your LG dryer, you will need a Phillips screwdriver or drill driver with a Phillips bit and needle-nose pliers.
2
Before you attempt this, be sure to turn off the power to the appliance.
3
Unthread the three screws securing the filter cover and remove it.
4
Pull the dryer away from the wall.
5
Unthread the five screws to remove the bracket.
6
Slide the lid and lift it off to remove from the dryer.
7
Unthread the two screws holding the control panel.
8
Pry the three tabs, then pull back and lift up to free the control panel.
9
Unplug the wire harness from the display PCB assembly.
10
Unplug the door switch.
11
Unthread the two screws on the lower half of the panel.
12
Unthread the three screws on the top half of the dryer panel.
13
Be sure to support the panel while unthreading the three screws that secure the top of the dryer panel.
14
Now lift and remove the front panel.
15
Now unplug the moisture sensor bracket, unplug the harness, and remove the routing clip.
16
To install the new moisture sensor wire harness, feed the wire through the dryer, insert the routing clip, plug in the harness, and plug in the moisture sensors.
17
Insert the panel in the two slots at the bottom of the appliance.
18
Now re-thread the three screws on the top half of the panel, re-thread the two screws on the bottom half of the panel, plug in the door switch, plug the wire harness back into the PCB assembly, insert the control panel into its grooves, and push forw
19
Then re-thread the two screws that hold it in place.
20
Place the lid on the dryer and push forward to secure.
21
Re-thread the five screws to reinstall the bracket.
22
Push the dryer back into place.
23
Next, align and slide the assembly into place within the dryer.
24
Re-thread the three screws to secure.
25
Turn the power supply back on, and your dryer should be ready for use.
Applicable Product Model
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com