Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Washer Dispenser Assembly Replacement ACZ74070508
This video provides step-by-step repair instructions for replacing the dispenser assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
LG Washer Dispenser Assembly Replacement ACZ74070508
Skill Level
Total Parts Cost
$195.72Estimated Savings
$112.5006:42
- Description
This video provides step-by-step repair instructions for replacing the dispenser assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the dispenser assembly in your lg washer, you will need pliers, a flathead screwdriver, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Detach the water supply lines.
6
Unthread the two screws on the top panel.
7
Slide and lift the top panel off.
8
Remove the twist tie from the hoses.
9
Slide back the tension clamp on the overflow hose.
10
Detach the hose end from the dispenser housing.
11
Loosen the clamp and remove the bellow from the housing.
12
Note the orientation and unplug the inlet valves.
13
Unthread the screw securing the valve bracket.
14
Slide and remove the bracket.
15
Noting the orientation, remove the valves from the bracket.
16
Open the drawer and push down on the “push” tab and remove the detergent assembly.
17
Unthread the two screws that secure the dispenser housing.
18
Push back and pull out the housing from its slots.
19
Starting with the smaller tab, pry the eight tabs to remove the housing from the dispenser.
20
To install the new dispenser assembly, place the dispenser on the housing and snap together in place.
21
Align the dispenser assembly in the two grooves and slide into position.
22
Rethread the two screws to secure the housing.
23
Align the detergent assembly and push in until it snaps into place.
24
Install the bellow to the assembly and tighten the clamp.
25
Insert the bracket in the panel and slide to lock in place.
26
Rethread the screw to secure the bracket.
27
Plug in the inlet valves.
28
Reattach the overflow hose, and set the tension clamp.
29
Reattach the twist tie.
30
Set and slide the top panel onto the washer.
31
Rethread the two screws onto the panel.
32
Reattach the water supply lines
33
Push the washer back into place.
34
Turn on the power, as well as the water, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the dispenser assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the dispenser assembly in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the dispenser assembly in your lg washer, you will need pliers, a flathead screwdriver, and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Turn off the water supply.
4
Pull the washer away from the wall.
5
Detach the water supply lines.
6
Unthread the two screws on the top panel.
7
Slide and lift the top panel off.
8
Remove the twist tie from the hoses.
9
Slide back the tension clamp on the overflow hose.
10
Detach the hose end from the dispenser housing.
11
Loosen the clamp and remove the bellow from the housing.
12
Note the orientation and unplug the inlet valves.
13
Unthread the screw securing the valve bracket.
14
Slide and remove the bracket.
15
Noting the orientation, remove the valves from the bracket.
16
Open the drawer and push down on the “push” tab and remove the detergent assembly.
17
Unthread the two screws that secure the dispenser housing.
18
Push back and pull out the housing from its slots.
19
Starting with the smaller tab, pry the eight tabs to remove the housing from the dispenser.
20
To install the new dispenser assembly, place the dispenser on the housing and snap together in place.
21
Align the dispenser assembly in the two grooves and slide into position.
22
Rethread the two screws to secure the housing.
23
Align the detergent assembly and push in until it snaps into place.
24
Install the bellow to the assembly and tighten the clamp.
25
Insert the bracket in the panel and slide to lock in place.
26
Rethread the screw to secure the bracket.
27
Plug in the inlet valves.
28
Reattach the overflow hose, and set the tension clamp.
29
Reattach the twist tie.
30
Set and slide the top panel onto the washer.
31
Rethread the two screws onto the panel.
32
Reattach the water supply lines
33
Push the washer back into place.
34
Turn on the power, as well as the water, and your washer should be ready for use.
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com