Price Match Guarantee
In-stock parts ship the same day
365-Day Return Policy
Price Match GuaranteeGET PRO PRICING
Video & Articles: Appliance & Equipment RepairLG Washer Display Board Replacement 4861FR3068A
This video provides step-by-step repair instructions for replacing the display board in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
LG Washer Display Board Replacement 4861FR3068A
Skill Level
Total Parts Cost
$326.84Estimated Savings
$112.5004:50
- Description
This video provides step-by-step repair instructions for replacing the display board in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the display board in your lg washer, you will need a flathead screwdriver and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Pull the washer away from the wall.
4
Unthread the two screws on the top panel.
5
Slide and lift the top panel off.
6
Unthread the screw securing the right side of the control panel.
7
Open the drawer and push down on the “push” tab and remove the detergent assembly.
8
Unthread the two screws that secure the left side of the control panel.
9
Pry the three tabs then pull back and lift up to free the control panel.
10
Unplug the harness to the control panel.
11
Pull off the control knob from the panel.
12
These next three steps will be difficult.
13
Pull back on the control panel, releasing the three tabs on the display board.
14
Squeeze the control panel and display board together and use a flathead to pry the board up.
15
Squeeze the panel and board together and pry the other side up.
16
Remove the display board.
17
To install the new display board, set one of the boards in the control panel and snap it into place.
18
Set and snap in the other board into the panel.
19
Align the control knob with the d-shaft and snap into place.
20
Plug the wire harness back into the display board.
21
Insert the control panel into its grooves and push forward to snap in place, rethread the two screws on the left side of the control panel.
22
Align the detergent assembly and push in until it snaps into place.
23
Rethread the screw on the right side of the control panel.
24
Set and slide the top panel onto the washer.
25
Rethread the two screws onto the panel.
26
Push the washer back into place.
27
Turn on the power, and your washer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the display board in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the display board in an LG washer (Model WM4000HBA). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
LG
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the display board in your lg washer, you will need a flathead screwdriver and a drill driver with a phillips bit.
2
Before you begin the procedure, unplug the washer.
3
Pull the washer away from the wall.
4
Unthread the two screws on the top panel.
5
Slide and lift the top panel off.
6
Unthread the screw securing the right side of the control panel.
7
Open the drawer and push down on the “push” tab and remove the detergent assembly.
8
Unthread the two screws that secure the left side of the control panel.
9
Pry the three tabs then pull back and lift up to free the control panel.
10
Unplug the harness to the control panel.
11
Pull off the control knob from the panel.
12
These next three steps will be difficult.
13
Pull back on the control panel, releasing the three tabs on the display board.
14
Squeeze the control panel and display board together and use a flathead to pry the board up.
15
Squeeze the panel and board together and pry the other side up.
16
Remove the display board.
17
To install the new display board, set one of the boards in the control panel and snap it into place.
18
Set and snap in the other board into the panel.
19
Align the control knob with the d-shaft and snap into place.
20
Plug the wire harness back into the display board.
21
Insert the control panel into its grooves and push forward to snap in place, rethread the two screws on the left side of the control panel.
22
Align the detergent assembly and push in until it snaps into place.
23
Rethread the screw on the right side of the control panel.
24
Set and slide the top panel onto the washer.
25
Rethread the two screws onto the panel.
26
Push the washer back into place.
27
Turn on the power, and your washer should be ready for use.
Applicable Product Model
Parts Needed
Display Board
$326.84
Total$0.00
Related Articles & Videos
Our Story
Family-owned and operated since 1912, Burke America Parts Group is the longest-running genuine appliance, HVAC, and outdoor power equipment parts solution in North America. At Repair Clinic, we're proud to be an international brand trusted by the pros as well as the DIY community.
About Repair Clinic
© 2026 RepairClinic.com